Fluid Power 11557

DN Staff

June 19, 2000

3 Min Read
Fluid Power

Valve manifold

The HM57 Five-Valve Manifold combines two shutoff valves, two equalizing valves, and a vent/calibration valve into a single, compact assembly. The double equalizing arrangement is designed to insure against measurement error that can occur from equalizer leakage between high and low pressure connections. The number of threaded connections is greatly reduced over needle valves, piping, and tees. Fewer connections leave fewer potential leak points. Available in carbon and stainless steel and some exotic alloys.

Hex Valve, 3170 Wasson Rd., Cincinnati, OH 45209; FAX (513) 871-0105; www.hexvalve.com.

For Information, circle 611


The HIPRES(R)welded bellow design accumulators seal the gas charge, eliminating recharging requirements. The all-welded construction does not use any elastomeric seals, so there are no seals to leak or wear out. The manufacturer claims that, due to this construction, no maintenance is necessary-providing lower costs. The product is designed to be unaffected by cold soak conditions and to withstand corrosive fluids.

Senior Flexonics Inc., 1075 Providence Hwy., Sharon, MA 02067; FAX (781) 784-1405; www.metalbellows.com.

For Information, circle 612

Valve gasket

Using a wire mill, the required bevels and grooves are wire drawn on the edges of petrochemical processing valves-eliminating the cost of machining the part from plate or sheet. Drawing is also reported to provide close tolerances and smooth edges, and outputs the finished shape on long continuous coils. The beveled or grooved wire can be produced in several metals, depending on the required corrosion resistance.

Ulbrich Shaped Wire, 55 Defco Park Rd., North Haven, CT 06473-1191; FAX (203) 239-6744; www.ulbrich.com.

For Information, circle 613

Pressure seal

This In-Line Pressure Seal is targeted for isolating pressure instruments from critical process medias. It is designed to 3A sanitary standards and allows unobstructed flow with no crevices, recesses, or constrictions that can cause clogging or contamination. The seal tube is flush 316 stainless steel, which is laser welded at the ends for a smooth interior surface. Possible industry applications include food, beverage, pharmaceutical, and chemical industries.

REOTEMP Instruments Corp., 10656 Roselle St., San Diego, CA 92121; FAX (858) 784-0720; www.reotemp.com.

For Information, circle 614

Hydraulic disconnect

The hydraulic pallet disconnect handle disconnects hydraulic lines from machine tool pallets or other applications. The handle is designed for double-acting hydraulic applications and operates at pressures of up to 5,000 psi. It automatically latches when pressure is present on either hose, preventing accidental disconnects. It must be used with a momentary hydraulic pump or 3 position 4-way valve in conjunction with a pilot-operated check valve.

Lexair Inc., 2025 Mercer Rd., Lexington, KY 40511; FAX (606) 255-6656; www.lexairinc.com.

For Information, circle 615

Solenoid valve

The SV51 Series direct acting, two-way diaphragm valves use a Dri-Solenoid(TM)designed to isolate the valve's metallic parts from the fluid being handled. It's offered in both virgin TFE Teflon(R)and a polypropylene body for maximum inertness and compatibility with a wide range of fluids. Featuring a bubble-tight shutoff, it's designed with a right angle body to provide greater flow per orifice size than comparable globe ported valves.

Valcor Engineering Corp., 2 Lawrence Rd., Springfield, NJ 07081; FAX (973) 467-8382; www.valcor.com.

For Information, circle 617

Sign up for the Design News Daily newsletter.

You May Also Like