HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
ltron
User Rank
Gold
Re: Good processor
ltron   7/5/2014 3:47:08 PM
NO RATINGS

It would be a major failing of the US education system to ignore the ARM Cortex M series. Basically the parts are destined to replace the entire 8 and 16 bit world IMHO. Of course universities are generally well behind the curve when it comes to to the real world.

Freescale now has out the low end of the Cortex M0 family with 8 and 16 pin parts for around $.50 in low volumes. This represents a part with higher performance, lower cost and power consumption than just about any 8 or 16 bit competitor. Finally after years of talking about it, an ARM processor really has the potential to replace the 8 and 16 bit world entirely.

In addition to that, it is built on a more modern process so it should not have the problems associated with process obsolescence like much of the existing 8 and 16 bit world. Obviously the various adherents to other silicon will still have their favorites but I don't intend to waste any more time with them. I mean you can still get 8051's for goodness sake but why would you want to?

Most of the historic Microcontroller folks have Cortex M solutions of some sort. In the US Freescale, Ti and Atmel have M4 solutions. I believe all three of them are working on M0 varients.

The Euorpeans have also been supporting ARM Cortex MX very well.

This is really great since it also fosters interest in the higher performance ARM families.

It would also be nice if the Arduino world would embraced the ARM Cortex M0 more but I imagine it will eventually or will totally lose relevance. It's really a shame they picked an 8 bit controller to begin with.

My 2 cents worth FWIW.

 

 

 

 

 

 

Cabe Atwell
User Rank
Blogger
Re: Good processor
Cabe Atwell   7/3/2014 4:03:07 PM
NO RATINGS
Did you know, most college students hardly learn how to use and particular chip? How much longevity will the M4 have?

 

naperlou
User Rank
Blogger
Good processor
naperlou   7/2/2014 10:27:55 AM
NO RATINGS
Rob, I have a development board for that chip.  It is a very good part.  One thing that is so impressive about the ARM Cortex-M series is the "layered" instruction set.  By that I mean you can get parts with the basic instruction set, or higher level parts with added instructions for various purposes.  The M4 is the highest level of the ARM Cortex series and has some great instructions including a FFT instruction done in hardware.



Partner Zone
Latest Analysis
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
The age of touch could soon come to an end. From smartphones and smartwatches, to home devices, to in-car infotainment systems, touch is no longer the primary user interface. Technology market leaders are driving a migration from touch to voice as a user interface.
Soft starter technology has become a way to mitigate startup stressors by moderating a motor’s voltage supply during the machine start-up phase, slowly ramping it up and effectively adjusting the machine’s load behavior to protect mechanical components.
A new report from the National Institute of Standards and Technology (NIST) makes a start on developing control schemes, process measurements, and modeling and simulation methods for powder bed fusion additive manufacturing.
If you’re developing a product with lots of sensors and no access to the power grid, then you’ll want to take note of a Design News Continuing Education Center class, “Designing Low Power Systems Using Battery and Energy Harvesting Energy Sources."
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service