User Rank
Re: Cost of modeling has to be considered
francisB   7/10/2014 1:34:48 AM
Cost Modeling is a common activity for any business. However it cost modeling cost forecasting rising cost of oil can also be a very challenging activity. In this introductory article, we will briefly talk about what it is, why small businesses should use it, the typical challenges a small business may face in doing cost modeling or forecasting and finally what tools and techniques are best suited for this activity. Informal reports are emerging that an increasing number of dealerships are beginning to scale back their markups on aftermarket insurance and financing. The dealer finance markup, as well as dealer insurance markup, could be pretty high as often as not.

User Rank
Cost of modeling has to be considered
storeng   5/15/2014 1:01:19 PM
While I agree that modeling on the long run is of extreme value, for many products, to have a model that has the needed precision, takes a lot of time and engineering efforts that are too costly for many companies.

When the cost is added to the modeling, and if on the long run makes the overall cost of developing or maintaining a product lower, then the development of the model is justified.

In the end the modeling has to be a cost diferentiator for the development of products.

From an academia point of view cost most of the time does not matter, the value is on the research results and this on itself has a cost that most of the time is at best ignored.

User Rank
Re: got to agree
CLMcDade   5/15/2014 10:20:21 AM
At some point in the education process, eliminating the rote, number-crunching task can seem desirable.  Concentration on teaching the theory and practical applications of the subject would seem to be a better use of that time.

On one level it probably is.  However, I remember many "a-ha" moments that came while struggling with the number-crunching.  Fighting to get reasonable results (or if we had it ahead of time, the correct answer) forced me to consider and reconsider my assumptions, my strategy and the constructs I had created to solve the problem.  Many times the theory stuck only after I personally worked through the problems.

And then there is the exercising of the brain that occurs while solving by "hand" - I'm not necessarily talking about doing long division or 5 digit multiplication by hand (though I believe that should still be a requirement in primary school), but instead working systematically through the steps of solving an equation.

While technology can be used to augment our education, there was a benefit to the rote memorization and repeated hand problem solving approaches that used to be emphasized in education.  Sometimes when benefits are intangible and invisible, they are easily missed when expediency and speed come into the mix.

User Rank
got to agree
naperlou   5/14/2014 1:33:37 PM
Raghavendra, I have to agree with you.  Since we usually use computers to solve problems in science and engineering, we should concentrate on coming up with and using the model.  This should, of course, be a change in emphasis.  I once took a graduate Computer Science class in computer architecture in which the half was a statistics class.  This was a complete waste of time.  The instructor should have just given out a supplemental write-up or text for that part of the class.  I find this happens often though.  There should be a basis of mathematics for engineering and science that is assumed.  A lot more could then be covered. 

I am currently working on a MS in Applied Statistics.  We use software exrensively, but the classes concentrate on modeling and interpretation.  This should be more the case in engineering.  I think part of the problem is a weakness in the mathematics requirements and training.

Partner Zone
Latest Analysis
General Motors is putting an off-road twist on hydrogen fuel cell technology with an imposing new pickup demonstrator called the Chevrolet Colorado ZH2.
Fine powder printing of industry-standard metal and ceramic powders with a grain size of less than 10 microns is now available from industrial 3D printer maker ExOne for its Innovent printer.
At ARM TechCon 2016, CEO Simon Segars will discuss how he sees billions of devices scaling to trillions as IoT applications proliferate. We know it’s happening. How do we prepare?
The term “autopilot” is now at the heart of a growing debate between Tesla Motors Inc. and Germany’s Federal Motor Transport Authority.
A make-your-own Star Wars Sith Lightsaber hilt is heftier and better-looking than most others out there, according to its maker, Sean Charlesworth. You can 3D print it from free source files, and there's even a hardware kit available -- not free -- so you can build one just in time for Halloween.
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 10 - 14, Embedded System Design Techniques™: Getting Started Developing Professional Embedded Software
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course September 27-29:
Sponsored by 3M
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service