HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 2/2
naperlou
User Rank
Blogger
Re: good replacement
naperlou   12/11/2013 3:33:51 PM
NO RATINGS
Nncy, good points.  With all the processing power they heve in the thing your suggestions should be easy to implement. 

Nancy Golden
User Rank
Platinum
Re: good replacement
Nancy Golden   12/11/2013 3:09:50 PM
NO RATINGS
I agree naperlou - we usually grab the smoke alarm and remove it from the vicinity until the smoke dissapates when we get smoke from cooking - it would be nice not having to do that.. I wonder if it distinguisheds between a gas leak and a fire in the alarm mode? I would also like to see a battery level autodetect that would send out a signal when the batteries needed to be changed.

naperlou
User Rank
Blogger
good replacement
naperlou   12/11/2013 12:13:19 PM
NO RATINGS
I need this.  We have a smoke detector that is in a bad (good) place to detect smoke from the oven.  Unfortunately, this goes off all the time and you have to blow the smoke away (we usually wave a towel).  I also like the communication options.  This is one useful device and it seems very well made.

<<  <  Page 2/2


Partner Zone
Latest Analysis
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
The age of touch could soon come to an end. From smartphones and smartwatches, to home devices, to in-car infotainment systems, touch is no longer the primary user interface. Technology market leaders are driving a migration from touch to voice as a user interface.
Soft starter technology has become a way to mitigate startup stressors by moderating a motor’s voltage supply during the machine start-up phase, slowly ramping it up and effectively adjusting the machine’s load behavior to protect mechanical components.
A new report from the National Institute of Standards and Technology (NIST) makes a start on developing control schemes, process measurements, and modeling and simulation methods for powder bed fusion additive manufacturing.
If you’re developing a product with lots of sensors and no access to the power grid, then you’ll want to take note of a Design News Continuing Education Center class, “Designing Low Power Systems Using Battery and Energy Harvesting Energy Sources."
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service