HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 4/5  >  >>
Jerry dycus
User Rank
Gold
Re: Using waste
Jerry dycus   11/27/2013 10:34:14 AM
NO RATINGS
Cruise ship as many others could easily do this. Easily gasified and fed into the engine, generator intakes to reduce fuel needs and pollution.

 

Not mentioned is 50% of plastics can be distilled directly into gasoline and diesel saving 50% of the cost.

Most other plastics can be made back into plastics.

A couple problems as shown gasification with air means low energy fuels as so much N2 over doubles it's volume.  Better to just heat it into a gas and go from there.

Next water content of the feedstock greatly reduces eff.

To get the best from garbage you need to keep it seperate, while more costly you get such higher value products, it's worth it.  10lbs of plastic equals 1gal gasoline/diesel.

Plus it creates jobs that pay for themselves and gives us a cleaner, lower cost environment. 

Habib Tariq
User Rank
Iron
Re: Using waste
Habib Tariq   11/27/2013 2:34:39 AM
NO RATINGS
This seems like a very good solution to the problem of plastic but any idea about what is approximate cost of setting up a gasification system and the running cost? It can be a key factor in determining the feasibility of this process? 

notarboca
User Rank
Gold
Re: Using waste
notarboca   11/26/2013 11:28:44 PM
NO RATINGS
Elizabeth, I am concerned about the tons of plastic and other wastes being discharged at sea instead of used for energy.  I wonder if a gasification plant could be constructed aboard cruise ships, providing fuel energy as well as reducing the overboard waste.

far911
User Rank
Silver
Re: Using waste
far911   11/26/2013 1:36:03 PM
NO RATINGS
As we know all the waste that cant be recycled and is being burnt to dispose of is resulting in damaging OZONE layer, which is very dangerous for the enviorment.

Ann R. Thryft
User Rank
Blogger
Re: Using waste
Ann R. Thryft   11/26/2013 1:14:47 PM
NO RATINGS
Thanks Elizabeth, I couldn't agree more.

Elizabeth M
User Rank
Blogger
Re: Using waste
Elizabeth M   11/26/2013 12:40:37 PM
NO RATINGS
Those are all interesting and relevant targets, Ann, I agree. I'm quite interested in what's being done in all of those areas as well, especially the first two, especially when it comes to plastic.

Ann R. Thryft
User Rank
Blogger
Re: Using waste
Ann R. Thryft   11/26/2013 12:29:17 PM
NO RATINGS
TJ searching the PDF of the report on "ash" produced these statements: "The combustion process and cleaning of the gases produce fly and bottom ash, further processed to remove metals for recycling. The ash can be used as alternative daily cover at landfills or as construction aggregate." There's also some further discussion of how ash is created and handled within different up-/down-cross-draft gasification systems.

Ann R. Thryft
User Rank
Blogger
Re: Using waste
Ann R. Thryft   11/26/2013 12:27:30 PM
NO RATINGS
Thanks Elizabeth and Rob. This is an area that interests me a lot, because it hits so many different targets: getting non-recycled plastic out of the environment, using waste creatively, re-using some already produced and very expensively-produced energy sources, and making non-petroleum-derived fuel.

Elizabeth M
User Rank
Blogger
Re: Using waste
Elizabeth M   11/26/2013 10:46:47 AM
NO RATINGS
I agree, Rob, and Ann has been on top of this. I really like to see the efforts around re-use of material, especially plastic, that would otherwise just become landfill or ocean pollution. If this material was created and used then it makes sense that it can be deconstructed and reused. Thanks for keeping a close eye on these efforts.

TJ McDermott
User Rank
Blogger
Re: Using waste
TJ McDermott   11/26/2013 10:27:47 AM
NO RATINGS
Ann, this was really interesting.  The other product of the process, shown in the last slide, is ash.  Did your sources say anything about it, such as what volume / weight percentage is it compared to the original feedstock, or if the ash has a use, its toxicity?

<<  <  Page 4/5  >  >>


Partner Zone
Latest Analysis
Adam Berger hacked a computer keyboard into a mini key-tar to play with his band.
Altair has released an update of its HyperWorks computer-aided engineering simulation suite that includes new features focusing on four key areas of product design: performance optimization, lightweight design, lead-time reduction, and new technologies.
At IMTS last week, Stratasys introduced two new multi-materials PolyJet 3D printers, plus a new UV-resistant material for its FDM production 3D printers. They can be used in making jigs and fixtures, as well as prototypes and small runs of production parts.
In a line of ultra-futuristic projects, DARPA is developing a brain microchip that will help heal the bodies and minds of soldiers. A final product is far off, but preliminary chips are already being tested.
If you're planning to develop a product that uses a microcontroller, you'll want to take note of next week's Design News Continuing Education course, "MCU Software Development A Step-by-Step Guide."
More:Blogs|News
Design News Webinar Series
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Sep 22 - 26, MCU Software Development A Step-by-Step Guide (Using a Real Eval Board)
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: September 30 - October 2
Sponsored by Altera
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service