Good point on quality Bobjengr. We've seen tons and tons of items in Made by Monkeys that would indicate there has been a sharp quality drop-off with American products since manufacturing shipped to Asia. It may be anecdotal as we see the complaints flow in, but I'll bet that represents a quantifiable drop.
Excellent Post Rob. I can certainly attest to the fact that time zones present a big problem. I retired from GE (Appliances). At that time, GE contracted with Satyam in India for all drafting and CAD work. It was a real pain for the "state-side" guys. We would start our communication meeting at 0600 hrs Eastern Time, just as they were leaving for the day. For me, that would mean leaving at 0515 in the morning to make the meeting on time. This really gets old in a heartbeat. Also, I don't want to be overly negative but, Satyam was not all that good because they simply did not understand American cooking products. India just does not cook like we do. The dishes are definitely different. We really struggled with this one.
I have one client that buys several products from China. Quality is questionable and you really never know if the product shipped will provide yields necessary to fulfill production demands. The very best company gives us an 82% yield. There is a 15% "over-purchase" knowing a significant percentage will be off-quality. This, to me, is completely unacceptable but the management is locked in to contracts that (apparently) can't be broken.
There is a great deal to be gained for bringing it home.
Debera, I was surprised when I found the time zones were an issue. But it makes sense. We're human. These executives didn't realize they would end up on the phone with their contract manufacturer every night.
@Rob, Yes working in different time zone is also a very important factor .I can understand the pain of working or staying in touch with the client during the night times thorugh different modes of communication. It totally disturbes your life , routine etc .
Good point Chuck. There are a lot of reasons to move manufacturing back to North America. I talked with an American executive in the electronics industry who moved manufacturing from China to Mexico so he could be in the same time zone. He hadn't anticipated spending every night on the phone with his contract manufacturer.
US has lost its manufacturing skills to China, Bangladesh and other less developed Countries like India, Brazil . US has been accused of becooming a service community. However there are certain companies that have started supporting manufacturing some products in US. I have heard somewhere that president of Wallmart US is planning to manufacture goods in US it would create jobs nd will boost the economy and the national pride.
Its really great that manufacturing is again comming back to US, i dont think that employees over there are not capable enough however in the past the wages in China , Bangladesh etc were less as compared to US but now there has been increase in wages and transportation cost has also rised so there is no advantage of placing the industry in Areas other than US.
Great article, Rob. I particularly like it because it shows that manufacturers of small items -- in particular, electronics -- are staying home. For a couple of years, we've been hearing that makers of big products (cars, trucks) lose their overseas cost advantages when it comes time to ship their big products back to the U.S. This shows that there are advantages to manufacturing here, even if you build small things.
It's not the learning curve that I question. I think that if the real problem isn't address, the opportunity to learn viable skills won't be present for years.
The possible delay I see is from U/S manufacturers acting like the proverbial ostrich and just sticking their heads in the sand. Or even worse, using the excuse of lack of affordable skills in the U.S. to go or stay off-shore.
Altair has released an update of its HyperWorks computer-aided engineering simulation suite that includes new features focusing on four key areas of product design: performance optimization, lightweight design, lead-time reduction, and new technologies.
At IMTS last week, Stratasys introduced two new multi-materials PolyJet 3D printers, plus a new UV-resistant material for its FDM production 3D printers. They can be used in making jigs and fixtures, as well as prototypes and small runs of production parts.
In a line of ultra-futuristic projects, DARPA is developing a brain microchip that will help heal the bodies and minds of soldiers. A final product is far off, but preliminary chips are already being tested.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.