HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Rob Spiegel
User Rank
Blogger
Re: Control and saftey
Rob Spiegel   11/18/2013 4:01:26 PM
NO RATINGS
I agree taimoortariq. There is the added benefit in set up, since you don't have to run as many wires.

far911
User Rank
Silver
Re: Control and saftey
far911   11/18/2013 4:40:52 AM
NO RATINGS
you are right, a better control and more safety will result in a better product and more output with quality with less hassel.

taimoortariq
User Rank
Gold
Control and saftey
taimoortariq   11/16/2013 11:39:45 PM
NO RATINGS
Certainly, its very efficient approach to provide control and saftey over the same ethernet network. Manufacturing plants can save up alot of energy by doing so and also increase there production by making the whole system more decenteralized.

Rob Spiegel
User Rank
Blogger
Safety has come a long way
Rob Spiegel   11/14/2013 3:21:53 PM
NO RATINGS
In just a few short years, safety in plants has changed significantly. I just visited the Rockwell Automation Fair where Rockwell Automation was demonstrating a free safety automation building tool:

http://www.rockwellautomation.com/support/configuration.page



Partner Zone
Latest Analysis
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
The age of touch could soon come to an end. From smartphones and smartwatches, to home devices, to in-car infotainment systems, touch is no longer the primary user interface. Technology market leaders are driving a migration from touch to voice as a user interface.
Soft starter technology has become a way to mitigate startup stressors by moderating a motor’s voltage supply during the machine start-up phase, slowly ramping it up and effectively adjusting the machine’s load behavior to protect mechanical components.
A new report from the National Institute of Standards and Technology (NIST) makes a start on developing control schemes, process measurements, and modeling and simulation methods for powder bed fusion additive manufacturing.
If you’re developing a product with lots of sensors and no access to the power grid, then you’ll want to take note of a Design News Continuing Education Center class, “Designing Low Power Systems Using Battery and Energy Harvesting Energy Sources."
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service