View Comments: Newest First|Oldest First|Threaded View
User Rank
Battar   11/5/2013 3:57:04 AM
"transform the manufacturing landscape"

"integrated collaboration tools"

" value-add services" " Insight is critical"  "glean better data from multiple touch points" 

"highest possible level of visibility and intelligence"

"a key reason for that shifting dynamic" " the agility needed to maintain a competitive edge"  "operations that leverage technology to its fullest" 

I challange you to re-write that article in English. Once you remove all the Dilbert-style management buzzwords theres not a lot of information left. It's little more than "collect data, and use it to make your production line more efficient". 

I think the editors of DN should have required the author to clean in up a bit, too. 

User Rank
Common Sense
ttemple   11/4/2013 8:15:23 PM
While I agree in general with what is presented, I have seen "systems" create problems as well, especially when the system is trusted over all other (human,  from the manufacturing floor) input.

An example that I observed several years ago was a plant that manufactures a catalog of small, relatively inexpensive widgets.  They make a small number of high volume widgets, and quite a number of others in various quantities, down to perhaps 12 dozen per year of certain models.

The plant went through the typical process of just-in-time, lean manufacturing, and computer driven workflow, etc.  A big emphasis was put on reducing changeover times for equipment, and making it quicker to produce parts in small lots.  Once this capability was achieved, the workflow system started injecting small lots into the production schedules in any way that made sense to it (the computer).

Because of the nature of the manufacturing process for the widgets in question, some quantity of parts are lost to machine setups, and destructive testing requirements.  So, every time a particular model needs to be manufactured, regardless of lot size, there will be some loss to the setup and testing processes.  The workflow system didn't seem to take these factors into consideration.

The end result was that instead of scheduling and manufacturing some profitable number of pieces, the system would kick out orders of perhaps 12 pieces or less of a product that would sell at a rate of 12 per month, year after year.

The common sense approach would be to produce 12 months worth of the parts, which may produce 4 or 5 scrap parts, instead of producing 12 per month, every month, and producing the same 4 or 5 (sometimes more) scrap parts each month.

The end result was that the company focused on their high volume parts and sent all of the "losers" to Mexico.  I would contend that most of the losers would be winners if they used some common sense in scheduling, instead of completely trusting the computerized system.

TJ McDermott
User Rank
Re: more data
TJ McDermott   11/2/2013 6:03:36 PM
Naperlou, in general I agree with all of your statements.  In the back of my mind though, I see echos of Robert McNamara applying similar methods to the soldiers in Vietnam, turning lives (and deaths) into numbers and efficiency factors.

User Rank
more data
naperlou   11/1/2013 10:53:22 AM
Some time ago I was given a tour of a building controls factory in the Chicago area.  As you walked on to the production floor there was a monitor with the status of each production cell displayed.  Of course, this information was provided by the MRP system.  Tying this type of information to external market data and making it available to the whole value chain can, as the article points out, make the whole enterprise more efficient.  It also helps management plan better.  This is definately an aspect of making US manufacturing more efficient, but more imortantly, more responsive.

Partner Zone
Latest Analysis
The company says it anticipates high-definition video for home security and other uses will be the next mature technology integrated into the IoT domain, hence the introduction of its MatrixCam devkit.
Siemens and Georgia Institute of Technology are partnering to address limitations in the current additive manufacturing design-to-production chain in an applied research project as part of the federally backed America Makes program.
Most of the new 3D printers and 3D printing technologies in this crop are breaking some boundaries, whether it's build volume-per-dollar ratios, multimaterials printing techniques, or new materials types.
Check out these gifts that will make you the hero of your Secret Santa party.
Voting has closed on our 2015 Gadget Freak of the Year contest, but it is not game over yet for two competing projects.
Design News Webinar Series
11/10/2015 11:00 a.m. California / 2:00 p.m. New York
10/29/2015 11:00 a.m. California / 2:00 p.m. New York
10/20/2015 8:00 a.m. California / 11:00 a.m. New York
12/2/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 6 - 10, Building Raspberry Pi Controllers with Python
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service