William K.
User Rank
Considering the noise, as well
William K.   10/14/2013 8:33:36 PM
This is an interesting and useful posting. But sometimes the readings from a noisy supply will be inacurate because of the noise on top of the DC output, and possibly on top of the input as well. An easy solution is to add filtering and read the voltage outside the filters. Usually the output voltage will be different with the noise filtered out, either higher or lower. Likewise the current, although it will usually be lower. This does reflect that noisy supplies are not as good as quieter ones.

User Rank
non linear loads
ChuckMahoney   10/14/2013 11:06:32 AM
This article seems to ignore the fact that most (those without active PFC) AC-DC power supplies are non-linear loads, and therefore the traditional concept of power factor doesn't apply. Current drawn by a typical SMPS (like a computer power supply) is in phase with the voltage since the bulk filter caps charge at the peak of the voltage waveform. The resultant waveform is severly distorted however. This is not the case if the SMPS uses active power factor correction. 

For non-linear loads, make sure to use a wattmeter designed to measure distorted waveforms. You can check for distortion by measuring the Crest Factor of the waveform using a DMM that has a peak capture mode and can measure true RMS. A pure sinewave will have a crest factor (Peak/RMS ratio) of 1.414. Any variation greater or lower indicates distortion. Typical SMPS current draw waveforms will have a very high crest factor, generally around 5. This indicates the typical "peaky" current waveform when caps charge at the peak of the voltage waveform. [voltage waveform distortion - especially in SMPS - tend to have crest factors less than 1.414 due to voltage flattopping]

An SMPS with active PFC will have sinusoidal (well, very nearly sinusoidal) voltage and current waveforms, and they will be in phase so input power is simply VrmsxIrms.

User Rank
Power supply efficiency
j-allen   10/14/2013 9:25:15 AM
If you need a wattmeter, an excellent and economical choice is the Weston 310 series.  These are the "Lab Standard" instruments in the mahogany cases rated at 1/4% accruacy.  Since they are electrodynamometers they measure true watts and they have no permanent magnets that can change strength over time.  You can check their calibration with DC using an accurate voltmeter and ammeter on the potential and current terminals, respectively, but it is best to flip polarity to check both ways.  

These instruments were very expensive when new (>$1000), but are now available quite cheaply on the used market.  And they are real works of art. 

Rob Spiegel
User Rank
Efficiency always
Rob Spiegel   10/11/2013 10:48:49 AM
This is just one more example of increased efficiency in power supplier. It will be interesting to see the cumulative effect of efficiency gains in so many areas.

Partner Zone
Latest Analysis
Designers of electronic interfaces will need to be prepared to incorporate haptics in next generation products, an expert will tell attendees at the upcoming Designer of Things Conference in San Jose.
According to a Randstad Engineering compilation of salary studies, engineering salaries are increasing beyond inflation, with employers paying to keep potential suitors away from their employees.
The company says it anticipates high-definition video for home security and other uses will be the next mature technology integrated into the IoT domain, hence the introduction of its MatrixCam devkit.
Siemens and Georgia Institute of Technology are partnering to address limitations in the current additive manufacturing design-to-production chain in an applied research project as part of the federally backed America Makes program.
Most of the new 3D printers and 3D printing technologies in this crop are breaking some boundaries, whether it's build volume-per-dollar ratios, multimaterials printing techniques, or new materials types.
Design News Webinar Series
11/10/2015 11:00 a.m. California / 2:00 p.m. New York
10/29/2015 11:00 a.m. California / 2:00 p.m. New York
10/20/2015 8:00 a.m. California / 11:00 a.m. New York
12/2/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 6 - 10, Building Raspberry Pi Controllers with Python
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service