HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
Ann R. Thryft
User Rank
Blogger
Re: Printed liquid metal
Ann R. Thryft   9/9/2013 1:05:10 PM
NO RATINGS
Thanks for the clarification. As an asker of pointy questions myself, I know what you mean. In this case, there's no damage or uncomfortableness on my end. Safety wasn't mentioned because it didn't come up.

William K.
User Rank
Platinum
Re: Printed liquid metal
William K.   9/6/2013 8:48:57 PM
NO RATINGS
Ann, sometimes asking pointy questions is a lot like throwing stones, in that they may cause some damage. Perhaps not the best analogy for this particular time, but really, the question about safety was made because safety was not mentioned. Sokmetimes the very most useful things are taken away because they are a bit toxic. Just look at lead in solder, as a good example of that happening.

William K.
User Rank
Platinum
Re: Printed liquid metal
William K.   9/6/2013 8:48:57 PM
NO RATINGS
Ann, sometimes asking pointy questions is a lot like throwing stones, in that they may cause some damage. Perhaps not the best analogy for this particular time, but really, the question about safety was made because safety was not mentioned. Sokmetimes the very most useful things are taken away because they are a bit toxic. Just look at lead in solder, as a good example of that happening.

Ann R. Thryft
User Rank
Blogger
Re: Printed liquid metal
Ann R. Thryft   9/6/2013 12:58:32 PM
NO RATINGS
William, thanks for the clarification. I like your use of that term, although I don't see how it applies to your earlier comment.



William K.
User Rank
Platinum
Re: Printed liquid metal
William K.   9/5/2013 9:05:25 PM
NO RATINGS
Ann, actually, I mean pointy, in that often, when they impact, they are uncomfortable. Plus, they tend to stick until answered. But you could also use the more traditional term of "pointed" and be correct as well.

Use of "pointy" desccribing questions is something that I learned during a course on how to keep people's attention duringpresentations I would be giving. A short course in showmanship was the other course I took at that time, both of them have been useful. An engineer who is quite at ease speaking to a room full of managers is more likely to be believed, no matter if he is right or wrong. And for people who don't understand the subject intimately, they do have to go by impressions.

Ann R. Thryft
User Rank
Blogger
Re: Printed liquid metal
Ann R. Thryft   9/4/2013 12:42:08 PM
NO RATINGS
William, you always ask excellent questions (I think you meant pointed, right?). Anyway, you'll have to ask the authors yourself for an answer to that one.

William K.
User Rank
Platinum
Re: Printed liquid metal
William K.   9/3/2013 4:27:30 PM
NO RATINGS
Ann, those two descriptors make me quite concerned, since they also describe mercury quite well. It also alloys with many other metals and also develops a very thin skin. Actually, it develops a thin film, I would not call it a skin.

So now comes a question about the toxisity of this wonderful new material. Isn't it awful when people keep asking pointy questions?

Ann R. Thryft
User Rank
Blogger
Re: Printed liquid metal
Ann R. Thryft   9/3/2013 12:02:58 PM
NO RATINGS
William, that was my concern, too about strength. There's not much in the article about this. The authors do describe one experimental prototype device, where "The liquid metal bridge connecting the LEDs functioned up to the strain limit of PDMS [polydimethylsiloxane] (Figure 4 b, ∼ 35% strain) and while being flexed without losing its electrical continuity."
Not much is said about electrical properties, but one thing they mentioned was that "electrical resistance remains largely unaffected because the skin is thin. In addition, the liquid metal adheres to most surfaces and alloys with many metals to form ohmic contacts."

William K.
User Rank
Platinum
Printed liquid metal
William K.   8/31/2013 8:33:31 PM
NO RATINGS
This is quite impressive but not quite jaw dropping. Some of these alloys have ben around for a while, such as Kirksite, a low temperature melting metal used for a number of things, and quite hard, also.

The electrical properties would be interesting to know, and I can see that it probably has a bit of resistance, so it would not work for high currents. My concern would be the lack of strength. Consider what could happen if the assembly with this material as the interconnect got bumped a bit too hard, and the connections rearranged themselves. THAT could be quite a pain.

Ann R. Thryft
User Rank
Blogger
Re: Extruded Metal
Ann R. Thryft   8/27/2013 4:23:38 PM
NO RATINGS
Isn't this a mind-boggle? To answer your question, the paper does not mention voltage at all. It does say "Injection of liquid metal into microchannels is an established method to shape the metal for reconfigurable wires and antennas, interconnects, electrical components for microfluidics, and "soft" electrodes for electrical characterizations of thin films."

Page 1/2  >  >>


Partner Zone
Latest Analysis
Some of our culture's most enduring robots appeared in the 80s. The Aliens series produced another evil android, and we saw light robot fare in the form of Short Circuit. Two of the great robots of all time also showed up: The Terminator and RoboCop.
Two students have created a voice-command system for our homes, based on the simple and affordable Raspberry Pi.
Optomec's third America Makes project for metal 3D printing teams the LENS process company with GE Aviation, Lockheed, and other big aerospace names to develop guidelines for repairing high-value flight-critical Air Force components.
This Gadget Freak review looks at a cooler that is essentially a party on wheels with a built-in blender, Bluetooth speaker, and USB charger. We also look at a sustainable, rotating wireless smartphone charger.
Texas Instruments is rolling out a new microcontroller that could make the design of sensor networks and data logging systems simpler and less costly.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 4 - 8, Introduction to Linux Device Drivers
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service