HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   8/19/2013 9:09:59 AM
NO RATINGS
EXAIR does have high temperature cabinet coolers. They are good for environments of 200 degrees F. They are of stainless steel construction so they are corrosion resistanct as well

Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   7/25/2013 2:11:18 PM
NO RATINGS
thanks for catching that. I need to Rich correct that for us

ratkinsonjr
User Rank
Gold
Re: Is it time for mil-spec in plants?
ratkinsonjr   7/23/2013 9:16:04 AM
NO RATINGS
O.K., Thanks, I get it now. The bottom of the panel is one of the small (2ft2) sides. BTW, the superscript for ft2 was dropped during editing of the original article, so the areas are shown as ft instead of ft2.

Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   7/23/2013 7:57:10 AM
NO RATINGS
Panel is 4' tall 2' wide and 1' deep

4*2 = 8 square feet surface area front

4*2 = 8 square feet surface area back

1*4 = 4 square feet surface left side

1*4 = 4 square feet surface lright side

1*2 = 2 square feet surface are top side

TOTAL surface area = 26 square feet

ratkinsonjr
User Rank
Gold
Re: Is it time for mil-spec in plants?
ratkinsonjr   7/22/2013 1:53:02 PM
NO RATINGS
I'm confused. In the example shown, there are three (3) dimentions for the panel area (2ftx4ftx1ft), but this should yield a volume (ft3), not ft2, as shown in the example. Assuming a rectangular prism with six (6) sides, there are two sides with 8ft2 each,two with 4ft2 each, and two with 2ft2 each, for a total surface area of 28ft2. Also, which side is the bottom surface that you are ignoring? Did I miss something? Please help.

Rob Spiegel
User Rank
Blogger
Is it time for mil-spec in plants?
Rob Spiegel   7/19/2013 12:58:14 PM
NO RATINGS
Nice article Joe. Quite enlightening. Is the potential solutioin to this mil-spec parts? Certainly ruggedized parts can better withstand high temperature even if they cost a bit more. 



Partner Zone
Latest Analysis
The popularity of Pokemon Go may be break open a new rush of augmented reality products.
Engineers in Australia have discovered a mechanism that could allow for the design of new composite materials for light harvesting and optoelectronics.
Here's a blast from the Gadget Freak past. Check out these gadgets, from telescope warming to keyboards on your fingers
A new method of modeling how they are created with chemical vapor deposition (CVD) could reduce the cost of carbon nanostructures used for for research and commercial applications, including advanced sensors and batteries.
BMW has already incorporated more than 10,000 3D-printed parts in the Rolls-Royce Phantom and intends to expand the use of 3D printing in its cars even more in the future. Meanwhile, Daimler has started using additive manufacturing for producing spare parts in Mercedes-Benz Trucks.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 11 - 15, Embedded System Design Techniques™ - Debugging Real-time Embedded Software – Hands on
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service