HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   8/19/2013 9:09:59 AM
NO RATINGS
EXAIR does have high temperature cabinet coolers. They are good for environments of 200 degrees F. They are of stainless steel construction so they are corrosion resistanct as well

Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   7/25/2013 2:11:18 PM
NO RATINGS
thanks for catching that. I need to Rich correct that for us

ratkinsonjr
User Rank
Gold
Re: Is it time for mil-spec in plants?
ratkinsonjr   7/23/2013 9:16:04 AM
NO RATINGS
O.K., Thanks, I get it now. The bottom of the panel is one of the small (2ft2) sides. BTW, the superscript for ft2 was dropped during editing of the original article, so the areas are shown as ft instead of ft2.

Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   7/23/2013 7:57:10 AM
NO RATINGS
Panel is 4' tall 2' wide and 1' deep

4*2 = 8 square feet surface area front

4*2 = 8 square feet surface area back

1*4 = 4 square feet surface left side

1*4 = 4 square feet surface lright side

1*2 = 2 square feet surface are top side

TOTAL surface area = 26 square feet

ratkinsonjr
User Rank
Gold
Re: Is it time for mil-spec in plants?
ratkinsonjr   7/22/2013 1:53:02 PM
NO RATINGS
I'm confused. In the example shown, there are three (3) dimentions for the panel area (2ftx4ftx1ft), but this should yield a volume (ft3), not ft2, as shown in the example. Assuming a rectangular prism with six (6) sides, there are two sides with 8ft2 each,two with 4ft2 each, and two with 2ft2 each, for a total surface area of 28ft2. Also, which side is the bottom surface that you are ignoring? Did I miss something? Please help.

Rob Spiegel
User Rank
Blogger
Is it time for mil-spec in plants?
Rob Spiegel   7/19/2013 12:58:14 PM
NO RATINGS
Nice article Joe. Quite enlightening. Is the potential solutioin to this mil-spec parts? Certainly ruggedized parts can better withstand high temperature even if they cost a bit more. 



Partner Zone
Latest Analysis
Lockheed Martin is looking to a new novel alloy and casting process to cut expenses on the F-35 Lightning II -- the world's costliest fighter jet.
After impressive test results, QM Power's Q-Sync fan motor has been identified as an emerging energy-saving technology and earned additional funding from the Department of Energy.
Henn'na Hotel, a next-generation, eco-friendly hotel in Nagasaki, Japan, is staffed almost entirely by robots.
With the pace of new editions and iterations, designers can fall behind quickly on software knowledge and skills. That's where JIT software training comes in.
After more than a century of dedicated service, metals are still upping their game and delivering lighter, stronger bodies and frames to the auto industry.
More:Blogs|News
Design News Webinar Series
6/25/2015 11:00 a.m. California / 2:00 p.m. New York
6/24/2015 11:00 a.m. California / 2:00 p.m. New York
6/11/2015 11:00 a.m. California / 2:00 p.m. New York
8/13/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 3 - 7, Developing, Testing, and Troubleshooting IPv4 and IPv6 Using Wireshark
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course August 25-27:
Sponsored by Stratasys
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service