HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
User Rank
Blogger
Re: Is it time for mil-spec in plants?
8/19/2013 9:09:59 AM
NO RATINGS
EXAIR does have high temperature cabinet coolers. They are good for environments of 200 degrees F. They are of stainless steel construction so they are corrosion resistanct as well

User Rank
Blogger
Re: Is it time for mil-spec in plants?
7/25/2013 2:11:18 PM
NO RATINGS
thanks for catching that. I need to Rich correct that for us

User Rank
Gold
Re: Is it time for mil-spec in plants?
7/23/2013 9:16:04 AM
NO RATINGS
O.K., Thanks, I get it now. The bottom of the panel is one of the small (2ft2) sides. BTW, the superscript for ft2 was dropped during editing of the original article, so the areas are shown as ft instead of ft2.

User Rank
Blogger
Re: Is it time for mil-spec in plants?
7/23/2013 7:57:10 AM
NO RATINGS
Panel is 4' tall 2' wide and 1' deep

4*2 = 8 square feet surface area front

4*2 = 8 square feet surface area back

1*4 = 4 square feet surface left side

1*4 = 4 square feet surface lright side

1*2 = 2 square feet surface are top side

TOTAL surface area = 26 square feet

User Rank
Gold
Re: Is it time for mil-spec in plants?
7/22/2013 1:53:02 PM
NO RATINGS
I'm confused. In the example shown, there are three (3) dimentions for the panel area (2ftx4ftx1ft), but this should yield a volume (ft3), not ft2, as shown in the example. Assuming a rectangular prism with six (6) sides, there are two sides with 8ft2 each,two with 4ft2 each, and two with 2ft2 each, for a total surface area of 28ft2. Also, which side is the bottom surface that you are ignoring? Did I miss something? Please help.

User Rank
Blogger
Is it time for mil-spec in plants?
7/19/2013 12:58:14 PM
NO RATINGS
Nice article Joe. Quite enlightening. Is the potential solutioin to this mil-spec parts? Certainly ruggedized parts can better withstand high temperature even if they cost a bit more.

 Partner Zone
Latest Analysis
General Motors is putting an off-road twist on hydrogen fuel cell technology with an imposing new pickup demonstrator called the Chevrolet Colorado ZH2.
Fine powder printing of industry-standard metal and ceramic powders with a grain size of less than 10 microns is now available from industrial 3D printer maker ExOne for its Innovent printer.
At ARM TechCon 2016, CEO Simon Segars will discuss how he sees billions of devices scaling to trillions as IoT applications proliferate. We know it’s happening. How do we prepare?
The term “autopilot” is now at the heart of a growing debate between Tesla Motors Inc. and Germany’s Federal Motor Transport Authority.
A make-your-own Star Wars Sith Lightsaber hilt is heftier and better-looking than most others out there, according to its maker, Sean Charlesworth. You can 3D print it from free source files, and there's even a hardware kit available -- not free -- so you can build one just in time for Halloween.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 10 - 14, Embedded System Design Techniques™: Getting Started Developing Professional Embedded Software
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course September 27-29: