HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/3  >  >>
vimalkumarp
User Rank
Gold
Re: 3D printing as a disruptive technology
vimalkumarp   7/16/2013 12:29:29 AM
NO RATINGS
you are spot on Jim in your analysis.

1. battery power in mAh ratings is directly proportional to the physical size of the cell. 2. The future applications are going to be toward much smaller, lower power devices . The second point is validated by the fact that MEDICA Dusseldorf as identified low power design as the medical device market driver. So if the design is low power, then even a battery wil less ampere hour rating can be used.

 

 

Ann R. Thryft
User Rank
Blogger
Re: 3D printing as a disruptive technology
Ann R. Thryft   7/15/2013 6:47:33 PM
NO RATINGS
Jim, that's a brilliant comparison. I'd still like to know exactly what process/materials they've invented and how it differs from others already in existence. The lead author, Jennifer Lewis, was quoted in an MIT Technology Review article here http://www.technologyreview.com/news/516561/a-battery-and-a-bionic-ear-a-hint-of-3-d-printings-promise/ saying that her team's method could print 2D and 3D electronics, including antennas, which sounds like the printed 3D electronic circuits Optomec is doing as we covered here http://www.designnews.com/author.asp?section_id=1392&doc_id=265097 although of course they're not made with thin-film. She also says the process is extrusion. Another similarity with Optomec is that in this same MIT article, Lewis talks about the potential for integrated electronics.

JimT@Future-Product-Innovations
User Rank
Blogger
Re: 3D printing as a disruptive technology
JimT@Future-Product-Innovations   7/15/2013 4:13:31 PM
NO RATINGS
Ann-You know what the article's image reminded me of, were MEMS devices, etched from silicon.  The 3D printing might be just the disruptive technology that the MEMS industry needed, as the silicone-etching process is so cost prohibitive.

JimT@Future-Product-Innovations
User Rank
Blogger
Re: 3D printing as a disruptive technology
JimT@Future-Product-Innovations   7/15/2013 4:07:01 PM
NO RATINGS
Remember that battery power in mAh ratings is directly proportional to the physical size of the cell.  While this is a breakthrough for 3D printing, there is a long way to go before it could power a pace-maker – if ever.  I think the future applications are going to be toward much smaller, lower power devices.

JimT@Future-Product-Innovations
User Rank
Blogger
Re: 3D printing as a disruptive technology
JimT@Future-Product-Innovations   7/15/2013 3:53:51 PM
NO RATINGS
Charles - your 800 uM estimate seems about right, from the scale in the image. It looks like 800 or maybe 1,000. 

But I have a difficult time envisioning uM's, or microns. In order to wrap my head around that tiny number I had to convert it to a unit I am much more familiar with, being either millimeters or thousands of an inch, which I understand better in my head. 

That image is  ~ 1,000 microns  ---  or, about 1.0mm  ---  or, about .040" .

When I see 1mm [.040"] now I'm clearly seeing a more tangible size -- about the plastic wall thickness of a common molded housing.

Still unbelievably small for a battery; but not microscopic. – (Just helps me to visualize it better.)

vimalkumarp
User Rank
Gold
Re: 3D printing as a disruptive technology
vimalkumarp   7/13/2013 11:56:20 AM
NO RATINGS
you are right, more voltage and more ampere- hour rating too.

vimalkumarp
User Rank
Gold
Re: 3D printing as a disruptive technology
vimalkumarp   7/13/2013 11:55:33 AM
NO RATINGS
you are right , the probability of powering sensors needing somewhat low power would seem to be a suitable candidate for this .

bobjengr
User Rank
Platinum
Re: 3D printing as a disruptive technology
bobjengr   7/13/2013 11:45:01 AM
NO RATINGS
vimalkumarp  --My thoughts exactly.  I know the technology is somewhat distant but when ready, I can see a device such as this powering a pace maker or maybe a pump implant delivering medication to a diabetic.  This is the type of life-saving R&D worth the time and money.  Also, the probability of powering sensors needing somewhat low power would seem to be a suitable candidate for this 3D device.  Great post Elizabeth.  Very informative.

Charles Murray
User Rank
Blogger
Re: 3D printing as a disruptive technology
Charles Murray   7/12/2013 6:28:31 PM
NO RATINGS
I would think an implantable defibrillator would require more voltage than this technology could supply.

vimalkumarp
User Rank
Gold
Re: 3D printing as a disruptive technology
vimalkumarp   7/12/2013 1:05:35 AM
NO RATINGS
Lonegity is also another important criteria in the batteries used for implantable medical devices. There is an increase in number and types of implanatable devices and power ratings of these are different understandably. Like rating for a cochlear implant battery may be different for ICD requirement and same is true with longevity.

Page 1/3  >  >>


Partner Zone
Latest Analysis
2016 engineering grads can expect to earn an average salary of $65,000 right out of the gate. Petroleum engineers' wallets are much fatter, though -- they are expected to earn about $20K more.
3D printing is now adding value to manufacturers at all steps along the business value chain. Come find out how at a talk by John Jaddou at next month's Embedded Systems Conference in Minneapolis.
From IoT and M2M to flexible robotics and consumer HMI, the advances in smart manufacturing are being deployed on the packaging floor.
These new 3D-printing technologies and printers include some that are truly boundary-breaking: a sophisticated new sub-$10,000, 10-plus materials bioprinter, the first industrial-strength silicone 3D-printing service, and a clever twist on 3D printing and thermoforming for making high-quality realistic models.
Ear-based heart-rate monitoring gained momentum recently, as sensor maker Valencell Inc. announced it has licensed its biometric earpiece technology to Samsung Electronics Co. Ltd for use in so-called “hearable devices.”
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 8 - 12, Getting Hands On with Arduino Mechatronics
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service