HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 2/2
mrdon
User Rank
Platinum
Re: Early, early CAD
mrdon   6/16/2013 6:20:44 PM
NO RATINGS
Rob,

I agree. Its amazing how Ivan Sutherland was able to conceive such a tool to aid in designing products. I remember when I was introduced to Computer Aided Graphics in college, the CAD station seemed magical. I really dugged the light pen as a drawing tool as well as the control panel which had buttons with pre-programmed shapes like circles, lines, and squares. The CAD 2.0 slides in Cabe's article really show how far the technology has gone and the imagination of its developers.

Debera Harward
User Rank
Silver
CAD Software
Debera Harward   6/17/2013 4:29:49 AM
NO RATINGS
Its quite interesting that technologies usually developed in early ages get advanced on and on and finally takes a new shape in future . CAD technology is no doubt example of this . CAD Software came into existance in early 1960 initially it was used in aerospace and automative industry only. Later on it became popular and is used in 2D and 3D printing currently there are different CAD softwaares in the market architecture cad software, home cad software and so on all these softwares helps to create 3D projects .

Cadman-LT
User Rank
Platinum
Great article
Cadman-LT   6/17/2013 5:19:44 AM
NO RATINGS
Great article Cabe. I really enjoyed it, I remember most of those beginnings. I had not heard of a few of the new ones though. I've been wanting a leap for some time.

Charles Murray
User Rank
Blogger
Re: Early, early CAD
Charles Murray   6/17/2013 6:40:00 PM
NO RATINGS
Thanks for the link, mrdon. I'll have to see if I can find that special on Netflix. I know there was a wartime codebreaking facility in Washington D.C., as well, codenamed CSAW (Communications Supplementary Activity - Washington (link below) that was responsible for tracking enemy subs in WWII.

http://www.businessweek.com/chapter/murray.htm

Tool_maker
User Rank
Platinum
I miss some of the old stuff
Tool_maker   6/18/2013 6:49:26 AM
NO RATINGS
  Very interesting article and a small chance to go down memory lane. I do miss much about hand drawing on a board. Some draftsmen were truly artists and could make drawings that had depth and looked like you could reach in and grab it off the paper. I miss the mental gymnastics required in all the trig involved in complicated designs. (I miss that because I was very good at it.) I do not miss the lettering, which in my case was often refered to as "chicken scratching" no matter how much I practiced. I do not miss the erasures of alterations or correcting a design. The callus is gone from my middle finger and the pencil groove is also gone, so I seriously doubt I could draw for eight hours without a sore hand.

  I also miss standing while working and the walking back and forth on a large design on my 7' board. I have tried CAD while standing with very poor results. But what I miss most is being able to bury an error. When I erased a mistake, it was as if it never happend, but today that error might have been reproduced a dozen times in different views etc.

  Do not get me wrong, I do not want to go back, but articles like this allow my mind to wander back to the good old days.

mrdon
User Rank
Platinum
Re: Early, early CAD
mrdon   6/18/2013 6:17:17 PM
NO RATINGS
Charles,

The CSAW sounds interesting. Thanks for providing the link: I'll definitely check it out!

<<  <  Page 2/2


Partner Zone
Latest Analysis
Lockheed Martin is looking to a new novel alloy and casting process to cut expenses on the F-35 Lightning II -- the world's costliest fighter jet.
After impressive test results, QM Power's Q-Sync fan motor has been identified as an emerging energy-saving technology and earned additional funding from the Department of Energy.
Henn'na Hotel, a next-generation, eco-friendly hotel in Nagasaki, Japan, is staffed almost entirely by robots.
With the pace of new editions and iterations, designers can fall behind quickly on software knowledge and skills. That's where JIT software training comes in.
After more than a century of dedicated service, metals are still upping their game and delivering lighter, stronger bodies and frames to the auto industry.
More:Blogs|News
Design News Webinar Series
6/25/2015 11:00 a.m. California / 2:00 p.m. New York
6/24/2015 11:00 a.m. California / 2:00 p.m. New York
6/11/2015 11:00 a.m. California / 2:00 p.m. New York
8/13/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 3 - 7, Developing, Testing, and Troubleshooting IPv4 and IPv6 Using Wireshark
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course August 25-27:
Sponsored by Stratasys
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service