HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
Page 1/3  >  >>
Cadman-LT
User Rank
Platinum
Re: Crash
Cadman-LT   9/2/2013 12:45:41 PM
NO RATINGS
Love the way you put that. After a failed overclock....lol

Cadman-LT
User Rank
Platinum
Re: Crash
Cadman-LT   9/2/2013 12:43:20 PM
NO RATINGS
Gotcha!

Cabe Atwell
User Rank
Blogger
Re: Crash
Cabe Atwell   8/27/2013 2:04:45 PM
NO RATINGS
It's like taking the cmos battery out of a motherboard to reboot the bios back to factory settings after a failed overclock. 

Cadman-LT
User Rank
Platinum
Crash
Cadman-LT   7/16/2013 11:01:20 AM
NO RATINGS
I know I am always rebooting my windows PC, I never knew you had to reboot your vehicle! Thanks for the info might come in handy some day.

Reliabilityguru
User Rank
Gold
Re: REBOOT
Reliabilityguru   7/15/2013 9:18:08 AM
NO RATINGS
I recently experienced the same problem with the CD player/changer in my wife's Escalade. After having the car in the shop for front strut replacement, the CD player wouldn't play CDs, and worse, the CD player motor wouldn't stop running even after the car was off and the keys removed. My worst fear was having to replace out of warranty the whole integrated CD/DVD changer, navigation system to the tune of untold $$. When I told my mechanic, he went immediatly to the fuse panel and pulled the fuse. Then he put it back and everything worked again good as new.

John
User Rank
Gold
Re: REBOOT
John   7/9/2013 4:45:24 PM
NO RATINGS
Often times a simple battery disconnect will "reset" the OBD system.  But if there are any significant warnings they will reappear from the memory that didn't get erased.  Sometimes 40 to 60 engine starts will erase error messages too.  If the computer doesn't receive the signal it took to trigger the error code during this time period. 

imagineer1000
User Rank
Silver
Re: REBOOT
imagineer1000   6/26/2013 1:17:01 PM
NO RATINGS
Agree it's an interesting post.  I've had two rental vehicles (different manufacturers) where the transmission just suddenly disengaged and the gas pedal stopped working.  What finally got the vehicles in gear again was cycling the ignition key.  Must be using a Windows operating system... ;-)  In all seriousness, I think vehicles are getting too complicated to be reliable in the long term.  I don't want my car to be like Microsoft Office where they have piled in more and more distracting "features" which offer fertile ground for introduction of more bugs without fixing bugs I first ran across a decade ago...

no_hazmats
User Rank
Iron
Rebooting
no_hazmats   6/10/2013 6:58:16 AM
NO RATINGS
I've had experienced mechanics mention to me several times that disconnecting the battery and also shorting out the disconencted battery cables for about a minute (to ensure complete reset and that non-volatile memory is cleared) is a good practice for oddball electrical & control system behaviors.  

bobjengr
User Rank
Platinum
REBOOT
bobjengr   6/8/2013 3:37:48 PM
NO RATINGS
This is a fascinating post.  In my wildest dreams I would never have thought a "horseless" carriage might need rebooting to correct issues with electrical equipment.  I'm a mechanical engineer and just don't think along these lines.  QUESTION: Since this seems to be one solution to several problems, do any of the manufacturers provide "re-set" switches to allow for the reboot process?  I have two older vehicles and there is certainly nothing in the use and care manuals to indicating rebooting might be necessary.  Just checked both to verify.

Ratsky
User Rank
Platinum
Re: Reboot also
Ratsky   6/4/2013 3:35:25 PM
NO RATINGS
That's certainly a good possibility.  However, I suspect that in general, a significant battery disconnect time will pretty much reset any sensors.  If the trigger conditions still exist, the sensor would trigger again eventually; if not, no harm, no foul!

Page 1/3  >  >>


Partner Zone
Latest Analysis
Futurist Raymond Kurzweil discussed biotechnology, solar power, and 3D printing at the Pacific Design & Manufacturing Show in Anaheim this week.
Valentine’s Day seems like a good time to recognize those folks around us who have had a hand in our success.
Makers of industrial PCs are continuing to take advantage of Moore’s law expansion of processing power enabling creative automation and control schemes with multicore processors.
Researchers at Lawrence Livermore National Laboratory have published two physics-based models for the selective laser melting (SLM) metals additive manufacturing process, so engineers can understand how it works at the powder and scales, and develop better parts with less trial and error.
The designer can now analyze temperature distribution in a design, tracking input and output of heat loads, and also turn it into a thermal stress study.
More:Blogs|News
Design News Webinar Series
1/28/2016 11:00 a.m. California / 2:00 p.m. New York
12/8/2015 11:00 a.m. California / 2:00 p.m. New York
2/18/2016 11:00 AM PT | 2:00 PM ET
2/24/2016 11:00 AM PT | 2:00 PM ET
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jan 11 - 15, Designing ARM Devices Using Segger Tools
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service