HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
Page 1/2  >  >>
Lisa hanawalts
User Rank
Iron
Resposibility of electrician!!
Lisa hanawalts   5/9/2014 3:02:05 AM
NO RATINGS
Electrical technicians have a big resposibity to be carefully solve electrical fault. Because electrical technical 's one mistake can lead to loss of property and life. I understand above problem how technical without knowing problem changes the fuse.

Cadman-LT
User Rank
Platinum
Re: Why???
Cadman-LT   7/16/2013 11:14:36 AM
NO RATINGS
And to think. I actually held repair technicians above most car mechanics. I guess it all depends on the person.

Cadman-LT
User Rank
Platinum
Re: Why???
Cadman-LT   7/16/2013 11:08:33 AM
NO RATINGS
Noswad...I think you got that right!!

Noswad
User Rank
Gold
Why???
Noswad   6/19/2013 4:04:43 PM
NO RATINGS
The repair technician had a nice and easy repair going that he could make a nice profit on and you went and screwed it up.

William K.
User Rank
Platinum
Re: Better solutions-
William K.   6/3/2013 9:39:18 PM
NO RATINGS
In aFender amp there are a few things that will make a fuse pop. A leaky filter cap will certainly cause a problem, as will a leaky cap across the cathode bias resistor. But the very nastiest ones are tose capacitors coupling to the output tube grids, because a leak there will also cause the tube life to be shorter by a large amount and possibly burn the output transformer, an item expensive to replace, if it can be found at any price. That is why I recommended replacing them with 600 volt units, or even 1000 volt caps. And the low leakage ones were the best choice.

tekochip
User Rank
Platinum
Re: Breaker Replacement
tekochip   6/3/2013 8:29:04 PM
NO RATINGS
It worked perfectly.  The replacement breaker was huge, but the spec was perfect.

William K.
User Rank
Platinum
Re: Breaker Replacement
William K.   6/3/2013 7:22:33 PM
NO RATINGS
So I am wondering if the replacement breaker worked out as intended? Or NOT?

tekochip
User Rank
Platinum
Re: Better solutions-
tekochip   6/3/2013 7:21:23 PM
NO RATINGS
 Being a huge Fender fan, I gotta ask, why in the world was the fuse blowing? The only one I ever took out was when my drummer knocked a Coke bottle off my amp and something akin to a Mentos fountain showered my 6L6s. The Coke shorted the plate to the filament, wiping out a 6L6, opening the hum balance control and burning the fuse. Fortunately there was a spare amp because it was the opening tune.


tekochip
User Rank
Platinum
Breaker Replacement
tekochip   6/3/2013 7:14:36 PM
NO RATINGS
I had a plasma TV that would frequently open its ill-sized, mini fuse. I was sure it was simply getting too hot in the fuse holder, so I replaced the fuse with a breaker that was carefully selected to have the same current and trip time specs.


ndjalva
User Rank
Iron
Re: Repairing laptop power supply
ndjalva   6/3/2013 4:51:18 PM
NO RATINGS
NEVER expect a service teck to know the answer, It was not on the page.......

I have nothing more to say.

Page 1/2  >  >>


Partner Zone
Latest Analysis
The engineers and inventors of the post WWII period turned their attention to advancements in electronics, communication, and entertainment. Breakthrough inventions range from LEGOs and computer gaming to the integrated circuit and Ethernet -- a range of advancements that have little in common except they changed our lives.
The age of touch could soon come to an end. From smartphones and smartwatches, to home devices, to in-car infotainment systems, touch is no longer the primary user interface. Technology market leaders are driving a migration from touch to voice as a user interface.
Soft starter technology has become a way to mitigate startup stressors by moderating a motor’s voltage supply during the machine start-up phase, slowly ramping it up and effectively adjusting the machine’s load behavior to protect mechanical components.
A new report from the National Institute of Standards and Technology (NIST) makes a start on developing control schemes, process measurements, and modeling and simulation methods for powder bed fusion additive manufacturing.
If you’re developing a product with lots of sensors and no access to the power grid, then you’ll want to take note of a Design News Continuing Education Center class, “Designing Low Power Systems Using Battery and Energy Harvesting Energy Sources."
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service