HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 2/6  >  >>
MSimon
User Rank
Iron
Re: WHAT TIME IS IT
MSimon   5/10/2013 2:08:24 AM
NO RATINGS
The grid might run 59 Hz it might run 61Hz, It will not be running at 55 Hz. Motors will burn out.

bobjengr
User Rank
Platinum
WHAT TIME IS IT
bobjengr   5/9/2013 5:56:16 PM
NO RATINGS
 Great post Jim.  Believe it or not, I had a similar experience with an ERC II (electronic range controller) when I worked for GE.  We absolutely could not understand why our on-board clock was losing time.  Not much time but it would lose approximately 10 to 15 seconds per day.  We contacted Robertshaw and they were baffled also.  One of our engineers, a EE type, had come to us from Louisville Power.  He made several phone calls and discovered the problem was just as you mentioned an input of 50 to 55 Hz instead of 60 Hz.  That solved our test problem.  Again, great post

jhankwitz
User Rank
Platinum
Re: Motor terminology
jhankwitz   5/9/2013 5:11:22 PM
NO RATINGS
Ah yes, the good old days.  We had one of those that would play a stack of four 20" glass 78 RPM records.

krruss
User Rank
Iron
Re: Motor terminology
krruss   5/9/2013 4:42:34 PM
NO RATINGS
Larry M 

Ok, I stand corrected - However, my point was to correct the idea that a synchronus motor and a squirrel cage motor are the same.  

 

 

Larry M
User Rank
Platinum
Re: Motor terminology
Larry M   5/9/2013 4:31:30 PM
NO RATINGS
krruss wrote: "A synchronus motor does have brushes, and requires a dc voltage on the rotor coil to lock it to the system frequency.  Since it does have brushes, and requires a separate power supply for the rotor, they are actually not very common."

Wikipedia suggests that there are several varieties of synchronous motor. One type, DC-excited, is produced in sizes greater than 735 W. Three other types of non-excited motors, reluctance motors, hysteresis motors, and permanent magnet motors. do not use DC excitation and do not have brushes. They rely on either induced rotor current or permanent magnets in the rotor. Each has different self-starting characteristics.

http://en.wikipedia.org/wiki/Synchronous_motor

 

 

Larry M
User Rank
Platinum
Re: Synchronous Clock
Larry M   5/9/2013 4:24:37 PM
NO RATINGS
Ahh yes. I'm also a geezer and I had one of those. Wikipedia suggests that small synchronous motors can be self-starting if load and the moment of intertia of the rotor are sufficiently low.

jljarvis
User Rank
Gold
Re: The grid affecting time
jljarvis   5/9/2013 4:14:17 PM
NO RATINGS
I'm not sure it was ever common practice, but I don't really know.  What was mystifying to me was how they were able to move the whole grid in a controlled fashion. 

Someone mentioned the tendency for slower generators to be 'pushed' by faster ones.  So perhaps there was a self-synchronizing effect across the grid.   The freq. shift must have been quite slow.  I've got a contact at Public Service Energy Group who would be in a position to know what happened. 

 

tekochip
User Rank
Platinum
Re: The grid affecting time
tekochip   5/9/2013 3:25:07 PM
NO RATINGS
I've designed dozens of clock-based appliances, and they all used line cross for a time base. Most of it is about money; if it plugs into the wall then line cross is free and a crystal costs money, a lot of money. Then there are some practical aspects of using line cross; the software can determine 50Hz or 60Hz using the microcontroller's internal oscillator, multiplexing the display can be synced to the line to prevent flicker with fluorescent lighting, if you know where line cross is you can phase fire triacs, you can "walk" relays by firing them at different parts of the linecycle to minimize relay wear and you know when the power has been interrupted long before VCC fails because line cross has ceased before the power supply bleeds off (handy for saving stuff in EEPROM and shutting the system down nicely).


jhankwitz
User Rank
Platinum
Synchronous Clock
jhankwitz   5/9/2013 3:08:13 PM
NO RATINGS
My parents had a synchronous clock on the mantel when I was growing up in the 40s & 50's.  It kept perfect time, but whenever we had a power outage the clock had to be reset and a small knob on its back had to be rotated to get it going.  It was a common prank to hold the knob to stop the clock at noon, and then spin the knob in the opposite direction to make it run in reverse.  We could tell what time it was by mentally transposing the numbers on its face, but it used to drive my old man crazy.

Thinking_J
User Rank
Platinum
Re: Wakeup
Thinking_J   5/9/2013 2:25:29 PM
NO RATINGS
Your proposed "experiment" could be flawed (depending).

Putting two oscillators of the same frequency (mechanical or electronic) near each other will demonstrate a strange affect. They will sync with each other. This gives an additional edge to the two time pieces tracking together in the same environment.

The experiment would be valid if the two time pieces are verified to track closely (but not exactly) with same temperatures - but physically separated enough to eliminate this effect.

The syncing effect is more pronounced with certain types of electronic oscillators. But can be demonstrated at some level in nearly all types.

I suspect using watches with metal cases and a modest distance would provide most of the required isolation to make the experiment valid.

 

<<  <  Page 2/6  >  >>


Partner Zone
Latest Analysis
Factory floor engineers may soon be able to operate machinery and monitor equipment status simply by tapping their eyeglasses.
GE Aviation not only plans to use 3D printing to mass-produce metal parts for its LEAP jet engine, but it's also developing a separate technology for 3D-printing metal parts used in its other engines.
In this TED presentation, Wayne Cotter, a computer engineer turned standup comic, explains why engineers are natural comedians.
IBM's new SyNAPSE chip makes it possible for computers to both memorize and compute simultaneously.
The “Space Kid,” 11, will be one of the first civilians to have his design manufactured in space by NASA, thanks to the City X Project, which inspires kids to think about new 3D-printed inventions that could be useful for humans living in space.
More:Blogs|News
Design News Webinar Series
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Sep 22 - 26, MCU Software Development – A Step-by-Step Guide (Using a Real Eval Board)
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: September 30 - October 2
Sponsored by Altera
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service