The mains where I live are not accurate to 20ppm, which is what I have come to expect from a 30$ Casio watch. But I don't use them, I wear 150$ Japanese automatic (mechanical) watches which are accurate to about 10 seonds a day. It's amazing that such intricate engineering can be sold retail at such prices. Anyone who wants a stable frequency uses a crystal oven, which uses a simple feedback controlled heater element in a sealed enclosure to maintain the crystal at a constant frequency - that trick is as old as WW2.
They do care a little bit, the IEEE, FERC and NAESB (North American Energy Standards Board) have very tight requirements for the frequency, voltage and other parameters for power quality. Without the standards it would be impossible to have reliable appliances or a distribution grid.
I lived in a neighborhood that was constantly browned out below the industry standard during heat waves. Each time the RMS voltage dipped below the minimum I called Commonwealth Edison to complain because I knew they would need to fill out plenty of documentation with the Feds (for negative reinforcement to be effective it must be immediate and severe). The real issue was load factor correction in a neighborhood that was built long before air conditioning. It only took a little over a week of complaining before they fixed the distribution problem.
The mains are more accurate in the US. Those crystals are very accurate when they are on your wrist, held to constant temperature. Less so in an outdoor transmitter hut or a room where air conditioning might not be present or cycles on and off.
Want to test it? Get two of those cheap crystal-controlled watches. Set them to the same time. Leave them in the same environment for a few days to assure they track. Then put one in the refrigerator or freezer and the other in a warm spot, e.g., in proximity to an incandescent light bulb. Check them after two days and notice how far apart they have become.
I would expect a commercial broadcast station to invest in the required equipment to maintain accurate time. After all, they already have an accurate clock source to drive the transmitter, don't they? This is a commercial enterprise we're talking about, not a HAM operator.
Hard to believe your clock radio normally uses the mains frequency as a time base in preference for its' on-board watch crystal. Which do you think is more accurate?
Synchronus motors and induction motors are not the same. An induction motor runs behind the synchronus speed, a syncrhonus motor is locked to it. An induction motor is the most common motor in the industrial world.
An induction motor (squirrel cage motor) does not have brushes. A synchronus motor does have brushes, and requires a dc voltage on the rotor coil to lock it to the system frequency. Since it does have brushes, and requires a separate power supply for the rotor, they are actually not very common. The generator at the power station is obviously syncrhronus. As noted in this story, some clocks are as well. In 28 years, I think generators and an old motor in the power lab at the University of Wyoming are the only large syncrhonus motors I have ever seen.
The poster is correct that the small throw away motors in vacuum cleaners, mixers, etc are universal motors.
At every power station I have ever been in, there is a meter generally on the back of the board where they track the frequency over a 24 hour period. Generally, the deviation is 10ths or 100ths of a hertz. Since the normal deviation is so small, I think the author showed pretty good trouble shooting skills finding this problem
What would you have had, 50 years ago, for an alternate clock source? Nothing was available. The pennies-cheap 32,768 kHz crystals and IC counters and LCDs that enable $1.00 watches and giveaway promotional stick-on clocks had not yet been cheaply mass produced. Timepieces were notoriously expensive and inaccurate. Think of the Rolexes and Omegas of the time.
I take issue with your statements regarding the "El-cheapo" clock radios. I have a couple of these (all under $US 10.00), from the usual Asian sources. They rely on the 60 Hx here in North Carolina, which is dead accurate. And if we do have a power outage, the 9-volt battery drives one of those 32,768 kHz crystals, not an RC circuit. I reset these exactly twice a year, at the beginning and end of the Daylight Savings Time period.
Perhaps a subtlety that y'all didn't pick up on: THE ENTIRE NATIONAL POWER GRID EAST OF THE ROCKIES WAS INVOLVED IN THIS EXPERIMENT. There being no HV transmission lines over the rockies, the left coast was... left out.
The idea was to see how much fuel could be saved if you ran just a few Hz slower in peak times (rather than having brownouts).... and catching up in null times like 3 am. They may have cared about the clocks, or they wouldn't have tried to catch up. At least, I figued they tried, but missed it by 5-10 seconds.
No big deal for your kitchen clock, unless you wanted the coffeemaker to come on precisely when network news did. :)
The interesting thing to me is that I never saw mention of a final report on the experiment.
El-Cheapo clock radios take the 50/6o Hz from the input transformer secondary and use is as a clock frequency instead of a crystal. The Clock/display driver IC usually has a 50/60Hz select pin which is jumpered on he PCB according to the market. These clock radios are notoriously inaccurate, because 50Hz is never quite what it says. It's worse if they go into backup/power out mode using a backup battery because then they rely on an R-C circuit. I understand all this happened 50 years ago, but even then, wouldn't a broadcasting station rely on at least on independent accurate clock source?
One of the early manufacturers of synchronous clocks would send salesmen to the operating engineers of power plants and give them one of their clocks, with the advice "If the clock is slow, just go in and speed up the generator 'til it catches up." Very clever marketing.
The same company went on to become the manufacturer of the first commercially successful electric organ which used a syncronous motor to drive its tone generator. Examples of these nearly 80 years old (I own a 1947 model myself) are still running great -- and in tune!
A new service lets engineers and orthopedic surgeons design and 3D print highly accurate, patient-specific, orthopedic medical implants made of metal -- without owning a 3D printer. Using free, downloadable software, users can import ASCII and binary .STL files, design the implant, and send an encrypted design file to a third-party manufacturer.
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This discussion will examine what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.