Interesting story, Chuck. I think it's a bit early to count out lithium ion, especially with some new research in different chemistries. But with all the negative publicity and the current limitations of the technology, there is certainly room for another battery chemistry to take its place.
If they could do something to improve the old technology that would be fantastic. Lead-acid is forgiving and easily remanufactured, but it's also heavy and has a poor life-cycle under constant use. It's great for starting cars, though.
Alternatives to the internal combustion engine. A dressed up older battery technology may help break through the difficulties. Or perhaps something else. So far it looks like lithium-ion will see some challenges.
Lead-acid batteries have lowest energy-to-weight and energy-to-volume designs, making them very big and heavy for the total amount of power that they can put out. But they do have a very high surge-to-weight ratio, which means that they have the capacity to deliver a big jolt of electricity all at once. This feature makes lead-acid battries perfect for applications that need a big, sudden surge of power, such as car starters.
Weight is a major issue. I have an electric mower that I modified so I could run from a battery pack and charge it with solar panels. Yes, a green lawn mower. It cost more than I will ever save in fuel, and the original 17AH SLA cells only last about three years. I repacked the mower with a 10AH NiMh that produces the same run time at about 1/3 the weight, a huge savings.
I only have one season in the NiMh pack, so I can't comment on life, but there is one downside. It's very easy to monitor the State Of Charge (SOC) for SLA cells, but impossible with NiMh. Since I charge with solar panels I have no way of knowing how much energy is going into the cells, so I had to add a Coulomb counter to monitor the charge. There are plenty of charge monitors on the market used for model aircraft and the like, but they have quiescent currents in the tens of mA range, not suitable when a cloudy day only yields that much from the panels, so I had to build my own monitor that idles in the uA range. Like I said, I'm never going to recoup the cost from fuel savings, but it's been a good learning experience.
So, from what I've learned, SLA is heavy, has a poor service life for a constant draw in the 1/2C range, but is very easy to monitor the SOC. The current NiMh technology is fairly light and handles a 1C draw very well, but you can't monitor the SOC very well.
Multiple problems from this PR. First I've driven lead power EV's for 15 yrs and they work very well thank you.
But the $ values in the piece have little to do with reality. If any OEM is paying more than $250/kwhr for Lithium cells they are fools. Retail is $400/kwhr with many reliable choices now. It's almost low enough to get me to switch and will when this set of batteries wear out.
Yet that is what the lead he says would cost. In fact OEM lead costs are well under $70/kwhr as I get them for that.
While lead is heavy and the rule of thumb is you need 100 lbs of battery/ 100 lbs of vehicle for an honest 100 mile range.
The way to make this work is make the vehicle lightweight, low aero, rolling, etc drag. This in as strong as a steel one would weigh 500-600lbs for a nice, safe 2 seater. So for 100 mile range you'd need just 600lbs of battery which equals 12 golf cart batteries.
As lead is by law 100% recycleable you just pay to have it reformed after the first set, $700 OEM which would be needed every 4-7 yrs or so at 50% of that.
But vehicles like that would only cost $8-10k and never rust away needing few parts and big auto can't have that!!
I should also note that all this is 1960's tech!!
But as lithium is lightweight and the 22lbs/kwhr are mostly common 1- $4/lb and only .5 of not expensive, $8/lb lithium. Iron, copper, alum, plastic, carbonate are most of the rest so within 5 yrs lithium will be as cheap as lead, winning the race.
I also use electric mowers, but I coose the plug in variety, so that I never need to recharge them or replace those short-lived battery packs. Now I am on mower #4, because they do wear out eventually, usually a motor failure. My friends with the batter mowers can usually get one mowing per charge, unless the grass is a little bit higher, in which case they can't mow the whole lawn at one time.
Probably the present level of development will be adequate for the stop-start driving mode, except for those vehicles with the air conditioning system running constantly. That mode is simply not compatible with stop-start driving. so while the best use of staop-start will both reduce pollution and improve mileage a lot, I can't predict that it will be accepted by a large portion of the driving population. Of course, it may be possible to produce a car that has a much lower cooling requirement so that the ten horsepower air conditioning system would not be needed. That is probably the single huge engineering obstacle that we have in store between current and future autos.
I'd like to see an unbiased analysis of the real, long term environmental impact of electric and/or electric hybrid vehicles verses internal combustion engines. These are touted as being green, but when the full impact of all these batteries is included, my suspicion is they will pale in comparison to a efficient IC engine. Europe, New Zealand, and Australia have been using clean burning 3-cylinder diesel engines that get 60 MPG for years. Meanwhile excessive government regulations and the green propaganda has clouded the US from a real technical assessment of the problem and the best solutions.
The company says it anticipates high-definition video for home security and other uses will be the next mature technology integrated into the IoT domain, hence the introduction of its MatrixCam devkit.
Siemens and Georgia Institute of Technology are partnering to address limitations in the current additive manufacturing design-to-production chain in an applied research project as part of the federally backed America Makes program.
Most of the new 3D printers and 3D printing technologies in this crop are breaking some boundaries, whether it's build volume-per-dollar ratios, multimaterials printing techniques, or new materials types.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.