HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 3/4  >  >>
naperlou
User Rank
Blogger
Re: Printing building
naperlou   4/11/2013 10:53:11 AM
NO RATINGS
Cadman-LT, are the machines you are talking about CNC or manual.  Frankly, if you are making any volume of a part, then more traditional machining will beat out 3D printing any day.  While the up front cost of a mold or tool may be high, amortized over many thousands of parts the cost is cheap.  If you are prototyping or doing very small production runs of complex parts, 3D printing should be the way to go.  In addition, 3D printing can be tied to many CAD systems making prototyping and visualization very cost effective.  You should probably get some of both.

Rob Spiegel
User Rank
Blogger
Re: Printing building
Rob Spiegel   4/11/2013 10:32:34 AM
NO RATINGS
Good points, TJ. I would imagine there will be a number of hurdles in getting 3D houses into production. For one, I can't imagine a house built from 3D parts would be cost effective. That may change, though, as the cost of 3D prnting comes down.

Elizabeth M
User Rank
Blogger
Re: Slow
Elizabeth M   4/11/2013 10:19:13 AM
NO RATINGS
Well, this is an impressive project, to say the least. Although I personally think that's quite a lot of money to spend on something that's just to prove that something can be done. But I guess you have to start somewhere! I think it will be a long time before actual buildings that are up to code will be 3D printed, though!

Charles Murray
User Rank
Blogger
Re: Slow
Charles Murray   4/10/2013 6:14:00 PM
NO RATINGS
Agreed, naperlou. This is about proving it can be done, more than anything else. 

naperlou
User Rank
Blogger
Slow
naperlou   4/10/2013 4:49:04 PM
NO RATINGS
While this may sound cool, 3D printing is VERY slow.  It is very good for low volume, complex and one off shapes.  Take, for example, concrete forms.  To do it the traditional way, you have to make a form, then you pour the concrete and you have your part.  The longest part of the process is making the form.  If you only have one to do, then maybe you 3D print instead.  On the other hand, at 5mm intervals it will take a VERY LONG TIME.  It would probably be better to make forms with 3D printing and then just pour the concrete.  It would certainly be faster. 

No matter how you do it, it would be equivalent in terms of being environmentally friendly.  That is not a consequence of 3D printing.  Perhaps he should look at the energy used in the printing as oppossed to various ways of making the forms.  That 3D printer will be using lots of energy at the 5mm thickness planned.  This is a calculation that is often overlooked.

Jennifer Campbell
User Rank
Gold
Re: Printing building
Jennifer Campbell   4/10/2013 4:32:49 PM
NO RATINGS
Cadman-LT, keep us in the loop regarding your plans. I would love to see what you come up with, and I think our readers would too!

Ann R. Thryft
User Rank
Blogger
Re: Printing building
Ann R. Thryft   4/10/2013 2:15:07 PM
NO RATINGS
Cadman-LT, are you planning on building something bigger than a breadbox, like a house, or are you looking to make tiny parts? And by machining equipment, do you mean CNC?



Cadman-LT
User Rank
Platinum
Re: Printing building
Cadman-LT   4/10/2013 1:00:34 PM
NO RATINGS
All apologies, that first message errord out...did not mean to double post.

Cadman-LT
User Rank
Platinum
Re: Printing building
Cadman-LT   4/10/2013 12:57:39 PM
NO RATINGS
Also, I am thinking small...maybe 1ft X 1ft max, if that helps.

Cadman-LT
User Rank
Platinum
Re: Printing building
Cadman-LT   4/10/2013 12:56:13 PM
NO RATINGS
Also, we are only looking at making smaller parts. I am guessing maybe 1ft by 1ft tops, if that helps.

<<  <  Page 3/4  >  >>


Partner Zone
Latest Analysis
The first Tacoma Narrows Bridge was a Washington State suspension bridge that opened in 1940 and spanned the Tacoma Narrows strait of Puget Sound between Tacoma and the Kitsap Peninsula. It opened to traffic on July 1, 1940, and dramatically collapsed into Puget Sound on November 7, just four months after it opened.
Noting that we now live in an era of “confusion and ill-conceived stuff,” Ammunition design studio founder Robert Brunner, speaking at Gigaom Roadmap, said that by adding connectivity to everything and its mother, we aren't necessarily doing ourselves any favors, with many ‘things’ just fine in their unconnected state.
When my daughter decided she wanted to study engineering, I was very proud of her. At the same time, in the back of my mind, I wondered if she knew what she was in for.
AutoDesk has teamed up with 3D scanner provider Artec to link CAD software and 3D scanners to make it faster and easier to create accurate 3D mesh models for printing or digital use.
Last year you helped Design News and Allied Electronics crown its first-ever Gadget Freak of the Year, and we need your help again. Vote in round 2 of our second-annual contest.
More:Blogs|News
Design News Webinar Series
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
11/6/2014 11:00 a.m. California / 2:00 p.m. New York
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Dec 1 - 5, An Introduction to Embedded Software Architecture and Design
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service