Excellent article. It's interesting how "building block" products play a role in continuing to make medical devices smaller and lighter. The environmental aspects of MPPE is a good bonus and increasingly becoming a decision point for consumers.
The article stated that the MPPE insulation is recyclable. With the use as a medical device, would the recyclability of the item be considered as a selling point for the device? Wouldn't medical devices be considered bio-hazzard after use?
Hi Tim- We cannot speak for the entire medical device, only our wire & cable. Frankly, I don't know what the procedures are for disposal of Medical Devices. I do know that Electronic Equipment typically falls under the Waste Electrical and Electronic Equipment (WEEE) Directive, and all of our EcoGen products (EcoWire, EcoWire Plus, EcoCable, and EcoFlex) are WEEE compliant.
Charles- It is definitely not limited to medical devices. That was merely the focus of this article, since we are trying to gain market share in the medical industry.
To be honest, we expect to sell a lot more to Industrial Machine builders, particularly with the EcoFlex product. EcoFlex has finer stranding and is very supple and flexible (hence its name). We are marketing it as a smaller/better/eco-friendlier version of the OLFLEX 190.
The improved wire insulation would also be useful for residential and commercial building wiring by allowing easier pull-through, more conductors in a given sized electrical box, etc. Do all you can to bring the costs down.
Most residential and commercial wiring is #14-#10 gauge, where all the wiring devices are set up to use solid wire. Connecting solid to stranded with a wire nut (as in ceiling fixtures) can be problematic, and the finer the strands the likelier it is that the strands simply wrap around the solid wire and the nut around the fine strands, with nothing to bite into the solid wire and keep the nut and stranded wire from slipping off. Switches, outlets, and other devices that use a simple screw with the wire looped around them, are very difficult, and probably illegal, to use with stranded wire, so a whole new set of wiring devices would need to be developed. Furthermore when using conduit of reasonably short lenghts, it's common to push the wire through directly, without using a fish tape or other pulling device. This is reasonably easy with solid THHN wire, with it's stiffness and slick overcoat, but would be next to impossible with stranded wire, especially wire that is especially flexible.
Note also that the codes specify the maximum number of wires allowed in a conduit based on the AWG of the wire and the current, because the limitation is one of heating rather than physical packing density, so if a conduit was currently packed to the maximum allowed using THHN, the thinner insulation of this new wire would not allow an electrician to put even more wires in that conduit.
I don't see any kind of flexible wire replacing TNNH or NM cable. Where it would be very useful is in control cabinets of industrial equipment where space is at a premium and tight bends are required. Most newer industrial control devices come with terminals that will work easily with stranded wire. That's a lot smaller niche than building wiring, but also a more valuable one if it saves installation time.
@apresher- You're somewhat correct. Most machine builders could care less about the environmentally-friendly attributes. However, the finer stranding and flexibility aren't exclusive to the EcoFlex product; these are common in PVC product as well. The size & weight savings are far & away the biggest differentiator for MPPE products to machine builders (and most customers). Now, I said you're somewhat correct because the smaller OD does make it more flexible than PVC (as flexibility is measured as a multiple of OD, and this has a smaller OD).
I should also add that in certain industries, such as Semiconductor Fabrication Equipment, the low outgassing is extremely valuable, as it doesn't emit a toxic gas that can damage the wafer. Semi equip't manufacturers have been designing around this for years (since they primarily use PVC cable).
Truchard will be presented the award at the 2014 Golden Mousetrap Awards ceremony during the co-located events Pacific Design & Manufacturing, MD&M West, WestPack, PLASTEC West, Electronics West, ATX West, and AeroCon.
In a bid to boost the viability of lithium-based electric car batteries, a team at Lawrence Berkeley National Laboratory has developed a chemistry that could possibly double an EV’s driving range while cutting its battery cost in half.
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This discussion will examine what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.