<<  <  Page 2/2
User Rank
Re: original ICU
Rocker3360   4/1/2013 3:09:32 PM
Yes this ignition was a points style ignition. It could be converted to magneto if desired. Electronic is way better!

User Rank
Re: Awesome!
naperlou   3/31/2013 9:46:12 PM
Let me second (or third or fourth) that.  This is a great project.  I love the combination of mechanical and electrical engineering.  I guess that's what Design News is all about.

User Rank
Re: Ignition control unit
Rigby5   3/27/2013 11:09:25 PM
When you can't adjust a variable venturi carb easily, it is almost always a case of the tapered needle being worn and needing replacement.  The taper is supposed to be continuous, but it will wear the most near the bottom, causing the mixture to be way too lean if you try to set the idle mixture right.  The needles are only a few bucks.

William K.
User Rank
Ignition control unit
William K.   3/27/2013 10:39:25 PM
This is indeed a neat gadget. But I did not see the actual circuit, which would have been quite interesting. Also a few more dtails in the photos would have been very welcome. My next bike will be a chopper, but I don't know what kind of engine it will have just yet. My last bike was OK to start, but the fuel mix settings were a screaming pain. When set for best power it would not start, when set for good starting it would not make power. Sold. Oh Well.

How about electronic fuel injection of a bike? Are the automotive injectors rugged enough for bike use?

User Rank
Re: Awesome!
AREV   3/27/2013 5:17:51 PM
I had a '67 BSA Thunderbolt w/ kick start. Nasty to start but always started on the last kick I had in me. After a couple of weeks I analized the process. I sat on the seat instead of standing on the starter, slowly rolled it and it started on the first time. Repeated from then on out. It was just playing with me.

User Rank
Ignition timing
stevejahr   3/27/2013 2:34:01 PM
Interesting design challenge to sync up with the motor within a single revolution.

Note that the actual timing requirements of the engine vary widely.  Not only does it vary dependent on engine RPM but even more so by cylinder pressure and also by fuel mixture.  Higher pressures burn faster and lower burn slower.  Lean mixtures burn slower too.  By way of example a classic Chevy V8 needs no more than 16* advance during cranking, 36* at full power/RPM, and 52* cruising.  Due to the low cylinder pressure and lean mixture at idle optimum advance is up in the 40's but many mechanical setups cannot get there.  An electronic mapping system with both RPM and MAP inputs can go a long way to optimizing the operation and efficiency of an engine.

Airplane ignitions have long had starting retard systems and so have some motorcycles.

Anyone interested in an extreme gadget here should investigate the Mega Squirt EFI system.  An entire system build to facilitate expirementation and learning of how these things work.

User Rank
original ICU
steamer   3/27/2013 12:26:30 PM
Nice project, big time commitment.  So was the original ignition conrol unit a mostly mechanical device, sort of like a distributor, points, and condensor for a car engine?

User Rank
I've been in combat with a Harley Evo for years...
Rocker3360   3/27/2013 11:25:18 AM
Awesome idea and design! I'm going to build this ignition in a nose cone mounted variety for the Evolution motor. Maybe this will alleviate some of the hard starting issues with a high compression motor. The MSD brand single fire ignition that is installed now, is a big dissappointment. (Single fire refers to each cylinder spark firing individually. The factory ignition in an evolution motor fires both plugs at the same time, known as dual fire or wasted spark). The problem I am having is when the initial static timing is set for the best starting, the total advance, though adjustable to some degree, is too far advanced and causes pinging on most premium fuels. The range of adjustment isn't wide enough to keep the total advance manageable. The MSD ignition allows the use of a VOES (Vacuum Operated Electronic Switch) to control the ignition advance switching point using manifold vacuum. These switches are inherently finicky. When they work, they work good, when they don't work... The circuit as designed will allow me to control the advance without this switch. I should be able to tailor the ignition "map" to my motor's needs. Now all I need is an ICU with a USB port to be able to edit the ignition timing while running...

Ride Safe Ride Smart


User Rank
Re: Awesome!
shehan   3/26/2013 10:18:23 PM
@Edward - This is simply a great project, I love this machine. It's nice to see we have ways of modifying this monster.

"I know a lot of Panhead owners who swear their motor starts on the first kick, which is probably true for the most part. But they will also tell you everything must be just right for it to come off on the first kick. I've also watched a few guys kick until they were blue in the face when things weren't just right."

Ohh yes not everyone knows the art of riding a Harley. As you said the rider need to know the correct technique and respect, this comes through experience.

User Rank
NadineJ   3/26/2013 1:51:59 PM
If I'd seen this, I wouldn't have sold my 1959 BSA C-15.  Kick starting is an art that very few have mastered.  My '89 Honda GB500 has an optional kick start.  It's an option I avoid.

Wonderful project!  This has great commercial appeal for fellow collectors.

<<  <  Page 2/2

Partner Zone
Latest Analysis
From wearables to design changes to rumors of a car, Apple has multiple things cooking up in its kitchen. Here are six possibilities from Apple next week, with likely more than one coming to light.
The key to the success of alt energy is advanced automation, which is still relatively new to the energy scene.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
New fastening and joining methods are making it possible to join multiple materials and thinner sheets in consumer and medical portable electronics, as well as automotive and aviation systems.
An upcoming Digi-Key Continuing Education Center class on designing motor control using MCUs and FPGAs will show you how to choose the best hardware and tools to speed up your development time.
Design News Webinar Series
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 9 - 13, Implementing Motor Control Designs with MCUs and FPGAs: An Introduction and Update
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service