mrdon, it's bad enough that commoditization means cheaper--often too cheap--materials and/or construction. But when the very thing that's one of a product's key characteristics--in this case a power supply's efficiency--is sacrificed by purchasing/accounting, that just beggars belief. I mean, trading off specs and features is part of the process but sounds like you had an exceptionally bad experience.
William, that's exactly what's been needed--for power supplies to become commodities so they'd be cheap enough and small enough. At least that was the push 20 years ago. But at that time, I didn't hear anyone complaining about what would happen when components were cheapened to reach that goal. Now I think we're all aware a lot more, as both designers and consumers, of the effects of this problem, whether it's cheapo plastic gears in clocks or sub-efficient power supplies.
Ann, You and TJ are absolutely correct about small size vs cost. One of my biggest challenges in developing LED Lighting fixtures while working at Hunter Fan was power supply efficiency, small size, and cost.To achieve a quality power supply, efficiency cost is part of the Product Development financial equation. I was able to obtain superb power supply efficient (99%) and small size using good PFC based components and proper PCB thermal management techniques, but the cost was something the Bean Counters couldn't stomach. Unfortunately, efficiency was the design parameter they could leave without.
Lower power/smaller size is only expected. What is troubling about the trend for the DIY/learning crowd, how does the average human place a 0603? Not easily. Will through hole components stay, or will pre-mounted small form factor take over? I am sure the price or old-style components will increase. The size and style of the through-hole resistor hasn't changed in decades, and they stay relevant.
Not only are the power supplies getting smaller, but many of them have become commodity items, with the result thatr there is a lot of price pressure. Unfortunately that tends to lead to a reduction in quality from many suppliers, while others chgarge a bit more for a better product. Consider that some of the better suppliers are able to sell a supply for amost twice the price of what others offer, a product with similar size and power ratings. So evidently in some areas quality and robustness still matter.
TJ makes a good point about price, of course. On a different price note, back when, some power supply designers said they could make advances closer to what was needed in size and efficiency, but that it would cost an arm and a leg to do so.
mrdon, those are exactly the reasons I was hearing 20 years ago that power supplies needed to get smaller, let alone more efficient. IR has long been in the forefront of advances in power supply design and manufacturing. At one time (maybe more than one?) industry pundits have said that power supplies were a major roadblock in advancing the state of electronics.
Ann, As pointed out in the article, todays electronics are getting smaller in size but the power requirements are going up. It's great that power semiconductor manufacturers like International Rectifier are developing technologies that meet both design requirements. I agree, its nice to see the arrival of this semiconductor technology in power electronics.
Thanks for reporting on this. I remember hearing about 20 years ago that power supply designers were trying to make their products smaller, but it was a tough job to make that happen. Looks like progress has been made since then.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
