I wish only subcontractors made these errors. About a month ago Verizon crew cut all the coper wires in the back of my house. When asked why the cut my phone, fax, DSL, etc... hey responded hat in a month or so we will get wired for FIOS.
GREAT SCHEDULING !!!!!
I'm sill fighing with Verizon to restore my phone and fax.
It doesn't even have to be an electrical contractor. One of my customers had the parking lot repaved and the PAVING contractor broke the ground connection for the electrical system. On a 480 volt system they were blowing uip items left and right.
@ Tim: Very true. You need to check the work and what sort of a quality level has been matched. They always try to finish stuff early as possible since they can take advantage of that and do someone else's work as well plus they also know that they do not get paid for time but for the work.
It maybe cultural, but it maybe governmental. Isn't this a government department? Or at least overseen by the government? How many times, even in American culture, that government workers tend to follow the beuracracies unfettered by thought or common sense?
And before you government workers bombard me with, "I do not do that!" I am only telling my experience. You may actually be smart and use common sense.
When our factory was moved to a new location the assemblers were given torque specifications for every threaded fastener because judgment calls were to be avoided in their culture. I would have product shipped to me to sample production runs and one unit caught my attention because something was rattling inside the case. When I opened it up I found that a potentiometer was loose. The nut had been tightened properly to torque, but it was cross-threaded. Certainly the assembler and inspector knew the pot was loose, but questioning authority was taboo, after all, the pot was tightened to spec.
Double checking sub-contractors is good advice. I recently worked on a job that required wiring low voltage communication and high voltage control voltage from valve sets to a main control panel. The bid job clearly stated that the control voltage and comm lines were to be seperate conduit to avoid interference between the lines. The contractor used the same conduir forboth to save time. Fortunately, we caught the error before signing off the project.
That's why I was wondering if it was cultural, Charles. In some cultures, thinking "outside the box" (such as calling engineering rather than following the replacement procedure which obviously wasn't working) is discouraged. For example, while two Americans may find two different approaches for solving a math problem and are congratulated on their initiative, in some cultures following the prescribed method without deviation is what is valued and they would have been chastized for using a different formula from the one being taught. Value systems and worldview affect us on levels we aren't even aware of and in ways that people from other cultures often find very puzzling.
People definitely get distracted, Ann. We always had company parties on site and everyone would be in a huge rush to finish up so that they could get to the party - it's very easy to overlook something that way. The parties were a lot of fun and great for employee morale though!
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
