Great presentations Fred. I am not able to listen live because my great IT support said it would take 3 - 4 days from them to give me special rights for streaming audio, Lol.. So I come home and listen after work. This is very interesting stuff, even though I don't have an application right now, I might down the road and this will be helpful. Looking forward to the last two days. Thanks again, Steve.
Again, thanks to everyone for joining our discussion today. And, thanks for the feedback on what you're currently working on and what you would like to see in this classroom.
Be sure to get your copy of the Bootloader schematic from http://www.edtp.com/dsn/microSD-Bootloader.pdf
I would say another "Con" is an opening for unauthorized modification. I have not looked ahead to see if you will address validation of the HEX file for security.
Got interruptd right at the end - use NXP Cortex M0/3 offerings. Fortunately many of the principles apply. Unfortunately we can't afford the board space to put an SD card on them (nor a display) so some of the princilpes will have to be modified. Think wall light switch with motion detector not a candidate for fancy interfaces.
Great lecture, Fred! Have you ever worked with the Freescale tower system? Some of those boards include a resident SD card slot. I'm also trying to learn about the TI MSP430 system.
@ctrlfreek: No I haven't. Sounds like it might be interesting to look at.
Is there a way to fail over to another hex file or another image (perhaps the last known good image) if BootApplication() fails?
@N3WWN: Yes..It's a simple matter of programming :-) For simplicity, I loaded a single .hex file to the microSD. You can have multiple files on the microSD all with differing images.
Instead of just collecting the one expected file, you could scan for them all and select the one you wish to load. If BootApplication() failed, you have had a catastrophic error occur and the NUKE button (ABORT) would have to be brought into play.
Well, Fred it will be interesting to see a presentation / project of a 32 bit MCU of any make with touch screen and SD bootloader card. State machine menu driven file system to bootload any of the many programs stored at the SD card. Thanks a bushel :)
@cmpatel: Most of them are contained in the Microchip Application Libraries. I'll supply the homegrown ones as a download. Download the MAL from the Microchip site.
Where can I find what TRISxxxx and LATxxxx are doing? I'm using them but have no idea what I'm doing.
@Kentj: Basically, TRIS determines if the I/O pin is an input or output. A 1 means the port pin is an input. A zero makes the port pin an output.
LAT is short for LATCH. LAT is always associated with an output pin. For instance, you write to LATDbits.LATD0 and read from PORTDbits.RD5. You set LATDbit.LATD0 to an output by writing a zero to TRISDbits.TRISD0. Conversely, you assign RD5 as an input by writing a 1 to TRISDbits.TRISD5.
Great lecture, Fred! Have you ever worked with the Freescale tower system? Some of those boards include a resident SD card slot. I'm also trying to learn about the TI MSP430 system.
Fred, since you answer all the questions together at the end of the lecture it's sometimes hard to figure out what question goes with the answer. It might be easier if you cut/pasted the question into the answer.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? Thats where the smart machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show whats possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
