Chances are your friend knew in advance there was a defect, hence the reduced price. This writer does not say he purposely bought some thing defective so he could save a few bucks.
Many years ago I was looking over a clearance table in a sporting goods store and found a fishing reel at half price, marked `AS IS'. I cleared a spot on the table and dismantled the reel and did not find anything wrong so I bought it. It has served me faithfully for 20+ years. However, at the checkout another man approached me and asked if I knew what was wrong with the reel. I told him I could not find a problem and he told me, "I took it apart and couldn't figure out what was wrong, so I was afraid to buy it."
Buying "defective" equipment isn't always a bad deal. A friend go a really good price for a radial arm saw. Apparently it would stall and trip on overload whenever the owner tried to cut something. It took only a few minutes to check the connection box and determine that the jumpers were set to 240 VAC but the cord was plugged into 120 VAC.
This post points to two of my biggest complaints. not only in industry, but everyday life as well. First is the lack of supporting documentation. I have griped about this before on this forum, so I will again. When I/we have spent thousands to purchase a piece of equipment or a software package they should come with an operators manual, including a section on trouble shooting. I would even be willing to pay an addtional amount, but instead you are lucky to get a web site or a phone number which is often peopled by someone who speaks with such an accent that everything after the initial greeting is impossible to understand.
The second and worst is a dealer who will resell defective equipment. It is impossible to believe these problems had not occurred before. The buyer should have been warned. If the original owner hid the problem from the reseller, than shame on him as well. What has happened to pride and integrity?
The quickest way to get deleted from my company's list of vendors is to supply defective parts or equipment and then not make the situation right. Particularly if the defect was known in advance. I wish the author of this article would have posted the name of the vendor to expose them for the frauds they appear to be.
That is like forgetting to connect the brake pedal on a new car- it steers fine, it accelerates fine, and the radio plays all your favorite stations. There's just this one little problem, so we will sell it to you cheap!
Isn't it amazing how expensive a simple design error like this can be to the equipment owner? The guys that design the system probably never realized that a broken thread was a normal event that happened frequently.
A few years ago when PCs were fairly new I did the electronics for a machine that utilized that I/O system having boards tied to a 64 conductor ribbon cable as the interface I/O bus. There was a huge design flaw in that if the control computer crashed, or stopped addressing the bus, all of the outputs would stay as they had last been set. Since this was a wet ful stand, that meant that gasoline would continue to flow if the system locked up, which happened daily while the testing program was being developed. The solution was a simple timer to pull down the master reset line whan it timed out after 1 second. The timer would be reset every 100milliseconds by the I/O write pulse if the control program was running, so under normal conditions the timer never timed out. We put the timer on the digital output board, since that was where control was most critical. But I never did find out why the makers of that system didn't even warn about the potential hazard.
That is a risky addition to the system. I had to add a similar circuit to a CNC motion controller's e-stop. I needed the controller's onboard capacitors to drain instantly. I wanted the motors to stop dead.
UK-based Plastic Logic and French company ISORG have created what the pair tout as a first in flexible printed electronics: a large area, conformable, organic image sensor printed on plastic.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
1 
