Sometimes the "bugs" have hair and a hearbeat. A grain dryer I repaired years ago... was reported, strangely, to have all the insulation missing from its wiring inside a control module. When I arrived and removed the cover, the report was correct, but failed to mention the skeleton of a mouse laying in the bottom of the box, along with a pile of colored PVC fragments located, more or less, where the little critter's stomach would have been at the moment of death. The little dude had eaten all the insulation off the wiring with his little chisel teeth, probably could not crawl out due to his increased girth from a belly full of nondigestibles, and simply expired there in the box. When the farmer came out to "power up" the console weeks later, arcing immediately kicked the controller off, and he called me. I rewired the box with XLPE wire [mice don't like XLPE] and it ran great after that.
I could rant for hours about how the current generation of appliance designers are completely out-of-touch with the actual useage of their products. My experience with an Amana range has sworn me off that brand forever. Within months of purchase, the plastic trim at the oven vent had become so embrittled that it literally crumbled away. Gee, you think the designer considered that it might get hot there? Duh ... try 400+ degrees! Of course, letters to them went unanswered ... and even worse, replacement parts were not available from the "factory".
My experience with bugs takes me back to working in the radio-TV repair shop for a huge department store in Florida (remember when radios could actually be repaired?). Opening the cabinet would often release a half-dozen huge cockroaches that would scurry across my workbench (they seemed to especially like to feed on paper speaker cones) to be "re-discovered" another day. I always kept a can of aerosol contact cleaner (in those days, TV tuners contained big multi-wafer rotary switches that, especially in Florida's climate, required periodic cleaning) on the bench at the ready ... it killed the critters pretty quick! I now live in California ... you couldn't pay me enough to live in Florida again! Bugs are just one reason ...
I have a microwave that has a fly stuck between the front window and the metal screen. It was alive for about 3 or 4 days and died. Its carcass is visible in the bottom ledge. For the life of me, I cannot figure out how it got there and will not take apart the door to get it out. I figure this is way to important to mess up the door and get overexposure to microwaves.
At least I did not have teko's experience. I think I would have tossed the control out the door if the surface was moving!
Gross. But interesting. I have heard of similar experiences with other appliances. Buttons getting stuck. Why do I need so darn many options. I don't need water in my fridge. I don't need 15 different cooking cycles and I really only want to have one washer and dryer cycle. Quit giving averything so much extra stuff that can break and design me a dependable appliance that lasts a long time so I can buy it.
When I lived on some acreage in the country, I discovered fire ants are extremely attracted to voltage. Telephone stopped working; telephone box outside packed with them. Air conditioning contactor would occassionally have to be sprayed as well. I learned something new every day.
Bugs do seem to get in the most inopportune places. I am sure the original design review for the stove didi not include "How do we stop bugs from getting in the controls?" Good sluething and not just throwing out the stove for a new one.
History repeats itself. Here's an explanation of where the term "bug" came from in the computer world (from Wikipedia): "Operators traced an error in the Mark II (computer) to a moth trapped in a relay, coining the term 'bug.' This bug was carefully removed and taped to the log book. Stemming from the first bug, today we call errors or glitches in a program a bug." The orginal incident occurred in 1946.
That indeed is a true case of debugging. I don't think I would have imagined that could be the source of the problem, so that's some pretty good sleuthing on your part! What a small thing to cause such a racket. At least the constant beeping didn't ruin your New Year's Eve.
I used to design agricultural electronics and the goods would come back from the field covered in grain dust and, shall we say, other barnyard commodities. One day I was pulling a keypad off of a unit and I noticed that the grain dust was moving in-mass like the tide rolling in on the beach. It turned out that the dust was really very small insects all moving together. From that day on I kept a can of Raid on bench right next to my soldering iron and used it time and time again.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
