Lighten up on Tesla. My money is on ANYONE ( I don't care if it's Black and Decker) with several years of experience with tens of thousands of cells in the market place vs. all the computer modeling in the world. I doubt that the computer models on any of the newer technologies are much good at this point.
The manufacturer of the cells is only responsible for the cells if they didn't build the entire battery.
Tesla crammed 6,800 laptop cells into a box with minimal monitoring. They blatantly ignored the manufacturers general recommendations.
They may well have gotten someone to agree to this but the point is that the Tesla design was very seat of the pants and not generally condoned. It was then hailed as a breakthrough.
Some breakthrough. Break all the rules and build a big bomb then hail this as some fantastic feat. I call it irresponsible grandstanding. Maybe its OK for a one off sports car but certainly not an airliner.
I find it very difficult to believe Boeing did not test to discover all of the failure modes possible with this battery system. I feel they must have and I would love to see a chronology of those tests and the pass/fail results. I don't suspect they will be published but it would be very enlightening. I think it would be prudent to explore all resources, including TESLA, when trying to find solutions to this problem.
To say Tesla has no right to talk about battery because they use commercial grade while Boeing used aviation grade battery is absurd. A battery is a battery no matter what grade it is. Fundamental principles are the same. In many case, avaition grade just means there are paper work and trace to go with the product. In many case, there are no difference in quality. That is why you see the trend in military and aviation going to COTS (commercial off the shelf) whenever possible to save money.
I appreciate Tesla's reasoning. The Batteries require space and channel cooling which will makes them to heavy for airborne equipment. Fact is the battery sensors did not respond is an issue. Since they proved to function then I assume the rapid heating cause the batteries to burst before the sensors detected the problem. Again these batteries need to be enviromentally screen in airborne mil-STDs to see if they can survive high altitude conditions with jet engine vibration. Since they failed too soon in life expectancy this indicates a problem.
Litium batteries are not properly built for space enviroment at this time. They have inherit mechanical design flaws that cause premature failures. in laptops, phones, cameras, now planes.
Ah it's the sheet metal case that apparently kept all the burning pieces inside. According to Boeing there is also a ventalation system to remove any smoke or fumes.
To me this is some level of evidence that Boeing forsaw this sort of failure. It looks to me like the thing got too hot and the safety systems did thier job.
The point is that Lithium batteries don't require active cooling. They require not getting too hot.
The main reason that active cooling is used is not to cool them while in a failure mode it is to keep them from failing in the first place. In a low load application this can easily be done with no cooling at all.
Adding cooling could be an additional safety risk in itself since it would greatly increase the complexity.
Actually if you recall it was the cooling system that caused the fire in the Volt battery pack!
going down mainly wrong tracks. There a number of potential problem sources, which could account for the failures. There are no guarantees that there are simple fixes. Prior comment about inbred, NIH. Based on my many decades of engineering involvement, I would like to presnet my list. I do not think Boeing should get a free ride, but a modest recompense, public thanks (technical acknowledgement) should suffice. Sannerwind@gmail.com JR/ CEO
Having seen dozens of pictures of the battery box, I cannot find any evidence of a physical containment system beyond the sheetmetal case. As lithium batteries are charged, they will physically swell slightly as they approach 90%+ SOC. Uncontained, each charge-discharge cycle slightly degrades internal structures through mechanical action. A prudent design will incorporate structural plates on either end of the battery stack connected with tensioned fasteners, preventing the physical distortion of the battery case by the internal components. '
The failure mode matches this model. Repeated charging slowly degreades the internal structures until an internal short is developed. The short would only be manifested upon charging as the battery once again flexes as it aproaches 100% SOC. The same situation likely occured during the development of the charger when an "event" burned down the development facility.
By experimenting with the photovoltaic reaction in solar cells, researchers at MIT have made a breakthrough in energy efficiency that significantly pushes the boundaries of current commercial cells on the market.
In a world that's going green, industrial operations have a problem: Their processes involve materials that are potentially toxic, flammable, corrosive, or reactive. If improperly managed, this can precipitate dangerous health and environmental consequences.
With LEDs dropping in price virtually every year, automakers have begun employing them, not only on luxury vehicles, but on entry-level models, as well.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
