WE did some experimenting back in the sixties, and later I learned from my father-in-law that back in WW2 when there was fuel rationing, they would run cars on mostly kerosene, after starting them on gas and getting them warmed up. Present engines are a bit more adaptable and probably have better sparking systems as well. What I learned from our experimenting in the sixties was that 10% diesel did work but much over that tended to run a bit rough in some engines. Our experiments were not very sophisticated, they were basically "add some of this and see what happens", and the results were observations done without instrumentation.
So there has been a bit of actual experience showing that it can work under some conditions.
Presently, the diesel fuel is more expensive so there is no incentive to use it in a gas engine.
I hear you regarding the Big Oil factor and I'm not one to take their word on anything. But the sponsor of this research is the NRC. And I simply don't believe this is invented out of whole cloth. Also, the report distinguished between three different kinds of emissions that you appear to be conflating: aerosol, black carbon and particle, with three different reduction rates.
I'm hoping they are on the level. From what I've read elsewhere, the aerosol emissions that were reduced in this case were "black carbon" or soot. We have the US military, ARA (US Military contractor), Chevron and Lummus representing big oil and NRC representing Canadian government all involved. With all their spin doctors possibly involved, it would be difficult for me not to question the "facts".
Nite_Owl, by "Fact or fiction?" are you actually suggesting that the Canadian government and its partners just made up everything reported here? I may be a cynic about some things, and I'm well aware that governments lie about some things, but I don't think all this would be orchestrated purely to deceive, nor can I imagine Canadians lying this badly. Also, note that the 50 percent reduction was in aerosol emissions, not particle emissions.
Interesting. I really hope this turns out to be at least half as good as they claim. The skeptic in me is worried by the numbers. A 50% reduction in emissions is huge. It's also hard to believe. I wonder if this Jet Biofuel has all the additives required for petroleum-based jet fuel. Foaming agents and other additives that are required to reduce flamability for fire safety do nothing to improve emissions. They are going to generate a lot of public interest with those numbers. I really hope they're factual.
From what I understand, heating oil is Kerosene #1 (K1), diesel is Kerosene #2 (K2) and Jet fuel is K2 with additives. I use un-dyed diesel (K2) in my furnace at home. Most diesel engines would run on either K1 or K2. The newer high-pressure injection diesels may have specific fuel requirements to prevent clogged injectors. I know that was a problem when they were first introduced in the US. Dual fuel filters and filter heaters were often required.
Since jet fuel is similar to kerosene, it should be possible to run a car on a mix of the two, To run a car on pure jet fuel would probably not work. But a diesel car may run on it quite well, but possibly not so well in colder weather.
Cabe, the needs of jet fuel and of automotive fuel are very different. That said, I'd like to know if this particular fuel solution can be done for cars, too. Meanwhile, stay tuned. I'll be posting soon on a different innovative automotive fuel source.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is