HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
<<  <  Page 4/6  >  >>
edsparks3
User Rank
Iron
Re: Were the Boeing 787 Batteries Cooled Properly
edsparks3   1/28/2013 5:10:05 PM
NO RATINGS
Ougassing should have been observed during tests.  True, low atmospheric pressure might accelerate outgassing but the atmospheric pressure inside a (pressurized) commercial aircraft cabin is generally in the range of normal. 

I also think vibration could be the culprit.  (see my comment, above).  

Charles Murray
User Rank
Blogger
Re: Design Decisions
Charles Murray   1/28/2013 5:06:41 PM
NO RATINGS
That's a scary thought, Bill. It's not hard to imagine Boeing deliberately choosing cobalt oxide for the higher energy density. That's its chief advantage over other lithium-ion chemistries and it's the reason many engineers choose that chemistry. But as for their alleged lack of a cooling system: It's anybody's guess. I think a lot of engineers are still climbing the learning curve when it comes to all the lithium-ion chemistries.

edsparks3
User Rank
Iron
Overheating?
edsparks3   1/28/2013 4:57:15 PM
NO RATINGS
I can't believe Boeing would use a battery design that was not so carefully bench tested that there was absolutely no way it could overheat no matter what happened to the charging circuit and no matter how little cooling was available.    

On the other hand it is quite possible that due to vibration in the aircraft, the electrodes might go into a vibrational resonance allowing a couple to touch each other and cause an internal short.  This could be difficult - but not impossible - to simulate on the bench.  

But it might answer a lot of questions. 

 

Charles Murray
User Rank
Blogger
Re: Were the Boeing 787 Batteries Cooled Properly
Charles Murray   1/28/2013 4:53:43 PM
NO RATINGS
Very good point, Paul. Elton Cairns of the University of California agrees with you. He told us that the higher, colder altitudes were a detriment, not an advantage in this situation. Cairns, by the way, should know: He designed the PEM fuel cells for the Gemini spaceflights in the 1960s.

apresher
User Rank
Blogger
Boeing 787
apresher   1/28/2013 4:51:29 PM
NO RATINGS
Given the importance of this issue to Boeing, I would be shocked if it kept the 787 down until 2014.  That would be a major setback to a very high profile program.  But I also think their engineers will also be very careful in avoiding missteps in implementing a solution to this problem. Not an easy thing to have the world watching while you solve a complex technical issue.

Elizabeth M
User Rank
Blogger
Re: Batteries, not composites
Elizabeth M   1/28/2013 4:50:32 PM
NO RATINGS
Yes, Ann, good point! At least it seems like that part of the design is sound.

Elizabeth M
User Rank
Blogger
Re: Let's hope they get the chemistry right
Elizabeth M   1/28/2013 4:50:00 PM
NO RATINGS
Well, good! If that's the way it has to be, that's the way it has to be. Better to wait until the design is completely safe to fly the fleet than risk human life.

Charles Murray
User Rank
Blogger
Re: Let's hope they get the chemistry right
Charles Murray   1/28/2013 4:47:02 PM
NO RATINGS
They will get it right eventually, Liz. But it could take a while. Over the weekend, CNET published a story in which they, too, interviewed Donald Sadoway of MIT. Sadoway told them that the problems could keep the 787 fleet grounded until 2014.

http://news.cnet.com/8301-11386_3-57566066-76/boeing-battery-solution-may-keep-787-grounded-until-2014/

Ann R. Thryft
User Rank
Blogger
Batteries, not composites
Ann R. Thryft   1/28/2013 4:25:02 PM
NO RATINGS
At least no one's blaming this on the plane's use of carbon composites.

Elizabeth M
User Rank
Blogger
Let's hope they get the chemistry right
Elizabeth M   1/28/2013 2:52:53 PM
NO RATINGS
If this is true, then it's a bit scary to think this could happen again. Let's hope engineers get the battery chemistry right next time so something like this doesn't happen again and cause an even more dangerous situation.

<<  <  Page 4/6  >  >>


Partner Zone
Latest Analysis
Major changes are happening in the world of 3D printing and additive manufacturing materials, machines, and software. If the industry -- and the design engineers and OEMs it serves -- are to grow, all three areas must become much more tightly integrated.
Americans spent more than $60B on their pets in 2015. Folks are definitely spending their money on more than dog food. We’re spending on things like dog spas and fancy toys, and as you can imagine, the wearables market is becoming well represented here.
Collaborating researchers in Australia and the United States have discovered nanotechnology for thermophotovoltaic cells that could boost solar-energy harvesting.
Time was when sports equipment was made only from common, everyday, low-tech materials. But now sports equipment has a new, high-tech ingredient that is helping players take their game to the next level.
Every now and then Design News likes to revisit some of our favorite Gadget Freak projects. Robotic hands, manipulated Kindles, and smart recycling cans round out the latest crop.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service