Again, I don't see any point in singling out (H)EVs here. Just legislate that vehicles should be no quieter than <N>dB. They should target the problem they're trying to address, not (H)EVs in particular.
I also find it ... odd ... that they seem to be imagining that all noise from a vehicle comes from the engine. Tire noise and air conditioners are at least as noisy as an idling engine on most small passenger cars.
I read through the press release. There is a lot of information that supports needing this.
Anecdotally, many in my area been hit by EVs and hybrids. As pedestrians, we rely on audible cues, such as deceleration, to determine safety. That's missing from EVs and Hybrids, leaving pedestrians and cyclists to completely rely on the driving skills and attentiveness of the person behind the wheel.
A Prius doesn't need to sound like a Harley to get someone's attention. There's a solution here if the emotion is taken out of the discussion.
This isn't *extra* noise as I read it, something I'm not at all fond of; this is making the same amount (more or less) of noise that gasoline engines make. Chuck, the cars are usually doing insane speeds in a 25 mph zone, on a blind curve no less. When I can't hear any coming (I have insanely good hearing), I know it's safe to do my super-fast U-ey. This will help a lot if it lets me hear them. Same goes if I'm in a garage or a parallel parking lot, where it's either hard to see or hear them coming.
I work for a company that has 80% blind direct labor. I've been wheeling my Prius around the company for several years without incident. After all, it's always been the driver's responsibility to look out for pedestrians, blind or sighted. It's not appropriate to honk your horn at a pedestrian to have them get out of the way. In effect, that's what they're proposing by including a speaker under the hood.
I'm concerned that, if they single out (H)EVs, rather than just making a general, minimum-sound-level law (which I also question the value of), then (H)EVs will end up being artificially noiser than gasoline vehicles!
Anyway, this appears to be where to comment upon this to the task panel investigating it:
I bicycle commute and when I am cruising there is so much wind noise that I can not hear most vehicles coming behind me. When I'm stopped I notice plenty of of tire noise from moving vehicles, and I've noticed that motor vehicles appear to be large enough to trigger visual clues as well.
It does seem to be a mandate without an actual cause. Is there a real danger, or does it just seem to be a good idea to pass legislation just in case it makes us all safer? It's strange how quick our country is to pass legislation on the perceived dangers of motor vehicles and how slow we are to passing legislation elsewhere when thousands of people really are being killed.
I have a 2012 LEAF wich has a nice beep-beep-beep sound when in reverse. No sound in forward though. I haven't had a problem yet but I appreciate the needs of the hard-of-hearing as we will all be that some day.
Since a safe sound is important for all cars, don't single out particular vehicle types. Just state the minimum sound level for all cars under 15 MPH that meets some 99% of peoples needs. Any car coasting to a stop can be as quiet now as an EV.
Also since loud sounds are much more of problem, mandate the max vehicle noise level for all vehicles at any speed. High noise affects everyone.
Speaking as a hybrid driver, I find this really annoying, since their quietness is a valuable feature. Also, there's no limit to how safe you can make a car, by reducing features. You can make it noisy like this, and then give it 2000lbs of safety features until it gets 5MPG and can't drive any faster than 10MPH! Plus, there wouldn't be any on the road anyway, because nobody could afford it. Thatwould be a very safevehicle!
The main thing that I think is "all wrong" about this is that they're addressing (H)EVs rather than the problem itself. They shouldn't cite (H)EVs, or even any particular speed range, and instead just say "no vehicle should be quieter than <N>dB." No value in tying it to any particular drive-train technology.
I agree. When I was kid I was told many many times "look both ways before you cross. These days people walk out in front of your car without even a glance in either direction, Often times with their eyes on their cell phones. Public awareness is the real issue, not the quiet new vehicles.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
