HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
REGISTER   |   LOGIN   |   HELP
Page 1/4  >  >>
Cadman-LT
User Rank
Platinum
Re: Good advice
Cadman-LT   5/18/2013 12:39:05 AM
NO RATINGS
Ann, but they Do say Leap is WAY better than kinect. I suppose that remains to be seen. I agree that it does depend on the project though.

Ann R. Thryft
User Rank
Blogger
Re: Good advice
Ann R. Thryft   4/10/2013 12:25:54 PM
NO RATINGS
A project starts with whatever technology is available at the time, so if it's the latest and greatest at the time, it's not exactly out of date. As I said, LEAP came out after they'd already started. And obviously, they don't think it's better than Kinect, at least for their project. Lots of people would agree with them: it depends on the project, and is often simply a matter of preference.

Cadman-LT
User Rank
Platinum
Re: Good advice
Cadman-LT   4/10/2013 11:53:49 AM
NO RATINGS
Ann next-gen system. Why start a project with out of date equipment. Isn't LEAP supposed to be so much better than the kinect? If they aren't even done with it why use old tech? It'll be out of date before it's launched.

Ann R. Thryft
User Rank
Blogger
Re: Good advice
Ann R. Thryft   3/11/2013 4:56:25 PM
NO RATINGS
Cadman-LT, the researchers described in that article said their next-gen system would use Kinect. At the time, LEAP either wasn't out yet, or had just been announced.

Cadman-LT
User Rank
Platinum
Re: Good advice
Cadman-LT   3/9/2013 11:46:06 AM
NO RATINGS
Ann really? Kinect? Kinect is shotty at best. There are better solutions than Kinect. LEAP if I remember correctly is one. 

Ann R. Thryft
User Rank
Blogger
Re: Good advice
Ann R. Thryft   2/25/2013 5:39:13 PM
NO RATINGS
Jack, do you mean the compression bands worn below the elbow? Yes, they actually work, at least on my mouse-arm.

Jack Rupert, PE
User Rank
Platinum
Re: Good advice
Jack Rupert, PE   2/25/2013 3:49:01 PM
NO RATINGS
Is that what those things are for Ann?  I've seen a number of people using those bands, but I could never figure out what they were used for...and didn't want to seem that nosy by asking.  I'll have to keep that in mind.

Cabe Atwell
User Rank
Blogger
Re: Good advice
Cabe Atwell   2/14/2013 11:25:42 PM
NO RATINGS
At CES 2012 and 2013 I saw a log of those reclining chairs with monitors suspended around them. You lay back like a dentist’s operating chair. Is that good? It seems like it take all the strain off the body, while at the same time making it weak. Reminds me of the chair the “genius” programmer from the movie “Grandma’s Boy” sat in. C

Ann R. Thryft
User Rank
Blogger
Re: Good advice
Ann R. Thryft   2/12/2013 4:06:00 PM
NO RATINGS
Thanks, Cadman-LT. That makes more sense. Regarding the article, the motion-capture tape was used initially for testing the software's accuracy in controlling a virtual robot, as the article states. The next-gen system will use Kinect to control an autonomous robot.

Cadman-LT
User Rank
Platinum
Re: Good advice
Cadman-LT   2/12/2013 9:58:23 AM
NO RATINGS
Ann,

 I just saw a hairbrush made in 1 pass by a 3D printer. So multiple materials....just neat.

Page 1/4  >  >>


Partner Zone
Latest Analysis
Eric Chesak created a sensor that can detect clouds, and it can also measure different sources of radiation.
Festo's BionicKangaroo combines pneumatic and electrical drive technology, plus very precise controls and condition monitoring. Like a real kangaroo, the BionicKangaroo robot harvests the kinetic energy of each takeoff and immediately uses it to power the next jump.
Practicing engineers have not heeded Yoda's words.
Design News and Digi-Key presents: Creating & Testing Your First RTOS Application Using MQX, a crash course that will look at defining a project, selecting a target processor, blocking code, defining tasks, completing code, and debugging.
Rockwell Automation recently unveiled a new safety relay that can be configured and integrated through existing software to program safety logic in devices.
More:Blogs|News
Design News Webinar Series
3/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
2/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
12/18/2013 Available On Demand
11/20/2013 Available On Demand
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Apr 21 - 25, Creating & Testing Your First RTOS Application Using MQX
SEMESTERS: 1  |  2  |  3  |  4  |  5


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: April 29 - Day 1
Sponsored by maxon precision motors
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service