Very good point about the previous predictions of higher voltages, Thinking J. Ten years ago, we were sick of hearing about the forthcoming arrival of 42V architectures. And where are they now? I would add, though, that hybrids an EVs have used higher voltages (upwards of 300V in many cases). But I agree with you that convntional IC engine-based vehicles will have 12V (14V) for some time to come.
Headlights use about 30-60 watts, regardless of whether they are tungsten, halogen, HID, or LED. There really isn't that much difference in power consumption between the best and the worst. There are of course significant differences in appearance, light levels, and cost; but not in power usage.
A car uses about 15 KW to move down the road at constant speed. That means the headlight's power usage is about half a percent of the total. The difference between the most and least efficient headlight is only going to be one quarter of one percent difference. That's a mighty slim improvement for lights that cost hundreds of dollars more.
My point was that going from a 90% efficient electronic DC/DC converter to a 70% resistor is even less signficant. It seems like a considerable increase in cost and complexity for an insignificant benefit.
On the fuel efficiency impact of daytime running lights: I *challenge* anyone to be able to measure the MPG impact on a statistically significant basis. It's "lost in the noise" and too low to detect!
If you want to save electrical energy in a car's electrical system, there is far more low-hanging fruit that would provide a lot more benefit for the buck. Use schottky diodes in the alternator. Use brushless DC motors instead of the ancient brushed motors. Design the electronics to draw micramps instead of milliamps.
I wrote NHTSA in the spring of 2011 asking them why they do not mandate constant headlight illumination on all North American Vehicles instead of DRL's. NHTSA responded with a 116 page document that basically said it was not "fuel efficient" to use full lighting 24/7 because of the load it pulled on the electrical system. So for you to say, "The power used by headlights is insignificant compared to the other loads in a car" would be a false statement if used in that manner. If NHTSA and the EPA both agree this load is enough to cause excessive loss of fuel mileage, then, in their minds, it IS significant!
My primary concern is safety and safety only. I could care less about the loss of fuel mileage for the use of constant headlights because the safety advantage greatly outweighs the difference in fuel savings. I would gladly give up one mile per gallon to be safe and for my children to be safe.....it's really not that big of a deal. In fact, both of my children turn on their lights every time they start their cars. It has become a natural reflex from day one, just like buckling their seatbelts.
Another concern I voiced with NHTSA, is that there is no taillight illumination with DRL's and some are actually so bright, that the vehicle operator thinks their headlamps are on. I see way too many people driving during the wee early morning hours and late afternoons with no headlights, and it isn't safe! One possible cause of this and another factor is the IP Cluster. On older vehicles, the cluster was never illuminated until the lights were turned on. The darkness inside the vehicle gave the driver an indication his lights weren't on, thus, triggering the reflex to pull out the switch. With newer vehicles, almost every IP cluster is being illuminated as soon as the vehicle is turned on. With this lighting inside the vehicle and the DRL brightness, most drivers think their lights are on, when in fact, they are driving down the road with or without DRL's and no taillights! Another factor is DRL brightness and the DRL being combined with the headlight bulb. Some DRL's are so bright that the vehicle operator cannot distinguish the difference between the headlight and the DRL's, thus thinking their lights are on. A good example of this would be the 1998 and 1999 Chevrolet Trucks, Tahoe and Suburban's. The DRL's are integrated into the headlight bulb and the brightness difference is barely distinguishable. DRL's should never be integrated into the headlight bulb. They should be a dedicated bulb placed in close proximity to the headlight, but not within, and the brightness should be at least, 50% dimmer.
With the new technology of LED's, these will draw less current on the electrical system and result in better fuel efficiency. My hope is that the auto industry, the EPA and NHTSA, will all agree that safety is a greater concern than fuel efficiency and LED's will help change our way of thinking for overall safety. Canada has already implemented full time DRL's and with this, anytime you turn on your windshield wipers, you lights come on. I say go ahead and mandate full time DRL's in North America and add taillight illumination. Remove the option to turn off your DRL's and make them automatic as soon as the vehicle is either started or is taken out of park.
James, I know you work for a semiconductor company, so ICs are a natural choice. But we're driving LEDs here. Why not just use groups of (say) 3 LEDs in series with a series resistor? The auto companies are fanatics about cost, and nothing could be cheaper than a simple resistor. No one has cared about headlight brightness variations with battery voltage in the past. The power used by headlights is insignificant compared to the other loads in a car.
While the general observations and comments are valid... Others are predicting the market in question (automotive) is going to be going though some changes. Changes that would impact assumptions being made.
- Change from 12(14)v system to higher voltages 36(42-48)v. reason: to get more power without impacting size / weight of system. Predicted before without happening. This time may happen because of expanded use of electrical systems in new vehicles has already taken place (hybrids, elect. based power steering, etc..)
- higher voltages with feedback system based on actual light output would negate much of the need for boosting (pre-regulation) on the lighting system. This would bypass the most of the effects of temperature, battery charge status and time on performance of the lighting system. Yea , this is complex also, but with complexity involving much lower power components.
Sounds like a really perfect application for those Digital Power microcontrollers, not only do you get the ability and flexibility of a uC for doing lighting/control tasks that have never been thought of, you can also implement the whole boost-buck, buck-boost, buck, boost, SEPIC, CUK, Flyback, Forward, etc... with just one chip. Microchip and Atmel are good places to start, and have many application notes.
James, this is a good overview of the desing choices for LED lighting. The ability to combine functions in one lighting unit are a great improvement. It should also offer new options that have not been thought of before.
I assume that although the control funcitons may be more complex, the available microcontroller circuitry should make it possible to implement.
Altair has released an update of its HyperWorks computer-aided engineering simulation suite that includes new features focusing on four key areas of product design: performance optimization, lightweight design, lead-time reduction, and new technologies.
At IMTS last week, Stratasys introduced two new multi-materials PolyJet 3D printers, plus a new UV-resistant material for its FDM production 3D printers. They can be used in making jigs and fixtures, as well as prototypes and small runs of production parts.
In a line of ultra-futuristic projects, DARPA is developing a brain microchip that will help heal the bodies and minds of soldiers. A final product is far off, but preliminary chips are already being tested.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.