HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Cabe Atwell
User Rank
Blogger
look it up
Cabe Atwell   12/27/2012 3:40:11 PM
NO RATINGS
This is all very detailed and complex. Most engineers I know have not used math beyond algebra or geometry in their day job careers. However, when faced with a problem, most engineers know where to look up info like the above. (The old cliche)

 

C

Greg M. Jung
User Rank
Platinum
Experience
Greg M. Jung   12/27/2012 9:48:14 PM
NO RATINGS
I agree that the ability to physically model systems is a valuable skill.  Having a good physical model can shed light on different areas of the design and accelerate system optimization and solution break throughs.

These skills are quite complicated to master and I think the main keys are gaining experience through practice and also having a good mentor.

EngineerPhil
User Rank
Iron
Re: look it up
EngineerPhil   12/28/2012 9:33:50 AM
NO RATINGS
Gents, after a few decades of doing this, good engineers do most of this

          in their heads, and only use the model to confirm thier conclusions!

 

          (and get hard numbers!)

 

          Phil

William K.
User Rank
Platinum
Re: Experience
William K.   12/28/2012 9:35:17 AM
NO RATINGS
The ability to produce an adequate model is very useful, but accuracy is omportant. One additional advantage of producing the model is that it serves as a "reality check" as it helps to  avoid missing pieces and details.

BUT attaching real numbers to a model does get quite tedious, while some of them can be looked up, othhers must be calculated.THAT can be very tedious indeed, I have found in the past.

Greg M. Jung
User Rank
Platinum
Re: Experience
Greg M. Jung   12/28/2012 9:24:10 PM
NO RATINGS
I agree.  In many cases, the real numbers needed for these equations must be empirically determined through experimental measurement (and that can get quite tedious, time-consuming and expensive when a project is on a fast-track).  Sometimes engineers want to take the time to run experiments to properly model the system, but management may not have the patience or commitment to allocate the needed resources and or allow the time to do it right. 

William K.
User Rank
Platinum
Re: Experience
William K.   12/28/2012 11:17:38 PM
NO RATINGS
Being able to procede without doing the modeling, or being able to do the modeling without doing all of the math, and getting it right, is the vaue of experienc, at least potentially the value. Knowing where you can't get away with assumptions is the biggest value of experience.

Scott Orlosky
User Rank
Platinum
Re: Experience
Scott Orlosky   12/31/2012 12:04:54 AM
Interesting discussions.  As a mechanical engineer who has made the transition into marketing and product development I can say that modeling (i.e. the mathmatical representation of the real world) is not confined to physical systems.  Buying behavior, pricing scenarios, market response to financial pressures all lend themselves to modeling.  Having the experience to look for these associations and the understanding to apply the correct modeling dynamics comes from my engineering background.

jmiller
User Rank
Platinum
Re: look it up
jmiller   12/31/2012 11:23:13 AM
NO RATINGS
I think taking time to write down the model can help insure that we don't miss one important detail which is ususally what happens when we do it in our head.

Greg M. Jung
User Rank
Platinum
Re: Experience
Greg M. Jung   12/31/2012 9:16:18 PM
NO RATINGS
Scott, well said.  Too many times, our engineering team delivered our product design on time, on cost and on spec. but the product didn't sell as well as anticipated.  Why? Because the buying behaviors as you stated below were also not properly or accurately 'modeled'.

D Hambley
User Rank
Silver
It's an art
D Hambley   1/16/2013 5:27:17 PM
NO RATINGS
Modeling of physical systems was not taught in school. I claim it's an art. When I have performed this "art", only other engineers who were intelligent enough to have done it themselves have understood. Experiance? No. As a new grad years ago, I had to model a motor driver / antenna / radar system. I had no experiance but I pulled it off. It required understanding that a derivative is the change of parameter A w.r.t. parameter B. Hmm, I couldn't understand why that concept was so difficult to grasp by others. One of the closed-loop parameters was the angle of the target. This was in radians. Another parameter was the electrical phase lag angle of the motor current. This was in degrees. "You can't mix degrees with radians" some people shouted." I remember this vividy from decades ago. They were actually angry. "You certainly can", I replied. Luckily for this new grad, there were other engineers in the room who understood simple principles of math and the model was accepted.



Partner Zone
Latest Analysis
Take a look through these film and TV robots from 1990 through 1994.
The Soofa is an urban smart bench that provides mobile device charging as well as collects environmental information via wireless sensors.
Sciaky, provider of electron-beam additive manufacturing (EBAM) services, will start selling these machines commercially in September. The company has used its EBAM 3D printing technology for making very large, high-value, metal prototypes and production parts for aerospace and defense OEMs.
At this year’s Google I/O, the spotlight was pointed on gender inequality in the high-tech industry. Google has established a new initiative that it hopes will even out the playing field, Made w/Code. Part of this initiative will fund free online courses in basic coding.
Self-driving vehicle technology could grow rapidly over the next two decades, with nearly 95 million “autonomous-capable” cars being sold annually around the world by 2035, a new study predicts.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 4 - 8, Introduction to Linux Device Drivers
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service