Lunar Regolith sounds a lotlike moon dust, which should be available in adequate quantities on the moon, it seems.
What are the mechanical properties of the parts fabricated thus far, and are they actually useable? I know that the first 3D printed parts were primarily useful for visualizing and not much else. But tha was in 1988.
Producing parts from the materials listed does not seem like they would be very tough, but rather very hard and quite brittle, unless some additional work was done on the mixture prior to laser sintering. I see a real challenge in providing a uniform particle size and uniform chemical composition.
Providing enough power to run the 3D printer is the other challenge that could be an obstacle to using the process onthe moon, although with an adequate solar array enough power should be available.
If more information is available a discussion of the properties of the material will be an interesting presentation indeed.
Didn't know that printing on the Moon or Mars would require working in a "zero gravity" environment. Low gravity, as compared to earth maybe, but not zero gravity. If you are going to be making stuff to be used on the surface it would make no sense to transport it to space and then back to the surface as that would have a heavy cost in fuel that would be in short supply.
William, both materials and processes are still in development, as we mentioned in the article. I think a bigger challenge than materials development will be the point you mention about power sources.
Ann, did you get a sense of what types of components will have the first priority for fabrication on the moon? I would imagine that the limited material available will also limit the variety of parts that can be fabricated.
If you mine the regolith on the moon's surface, there are actually quite a bit of materials that can be processed. Different locations on the moon will result in different percentages in composition. My employer, Teledyne Brown Engineering (TBE), has worked with Marshall Space Flight Center (MSFC) on In Situ Fabrication and Repair (ISFR) where we looked at using lunar regolith as a feedstock for additive manufacturing as well as other complementary projects. We specifically looked at the EBM process. With the EBM using a vacuum in their build chamber, the lunar environment is an excellent one. We have looked at mining oxygen from the lunar surface and using the waste products from this process (metal oxides), converting it to powder, and using it as the feedstock. It is certainly possible. There is titanium and other metals available on the moon.
We have looked at mining this material, as well as combining all metal "waste", and also looking at the lunar regolith. We did this work 4-5 years ago using a couple different simulants. We made some brick samples using lunar simulant along with a binder. The funding stopped and we could not continue this work. The funds were re-directed to more short-term work such as building a new rocket to replace the shuttle fleet! Other areas of interest included non-destructive inspection of additive manufactured parts such as Microwave and millimeter wave nondestructive testing and evaluation methods. We looked at post-processing these AM parts to arrive at acceptable tolerances. We even looked at growing biological parts as well as producing electrical components such as PC Boards and discreet components.
I'm glad to see additional work being done in this area. We spent 4-5 years working on everything from a lunar base to documenting possible existing parts on the ISS that could be replicated using additive manufacturing in space. NASA is very interested in looking at in situ manufacturing and this work will help make it happen. We worked with the Contour Crafter in building habitats and building launch/landing sites.
This was some really fun work. Hopefully, we can get the project going again and help make some significant progress!
Greg, to answer your other question concerning what components will be fabricated first, you have to decide what spares make sense to bring with you. In some cases, the upmass makes sense to bring the spares. I think the first things to fabrciate may be simple tools or unique tools made for specific applications. Additionally, the exercise equipment is always in need of repair on the ISS so I could see some repair parts for the crew health equipment.
Greg, most of what I've read mentions simple tools and replacement parts would be the prime candidates. But then there's also the idea of making structures, like Contour Crafting has proposed http://www.designnews.com/author.asp?section_id=1392&doc_id=250614 JimG, thanks for weighing in with your direct experience. I think this is a very promising and exciting area to be working in.
Jim, thanks for your insider information on the subject. Here's hoping we have a good reason to go back to the moon to take advantage of this and other developments.
I have to agree. I never thought of all of the things you would have to do without while being up there. It's not like you can just go down the street and pick up a screw at the local hardware store.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
1 
