Elizabeth, this is a very useful tool for the construction industry. Designers can check their design for strength and accuracy, but many problems in buildings are caused by construction errors. Some of these errors are in measurement, and this system is a great complement. Of course, there are errors that are more related to process that are not addressed. Therefore, while some contingency money will be saved, perhaps, it is not going to be possible to eliminate it using this system. Frankly, in the construction industry, hours lost are hours lost. I don't think that they will be applied to something else. That is not really a problem for society in general, but it could be for construction workers.
Depend on how cumbersome it is to use the bots, I see this as a great new tool. I don't see it having much of an impact on the drafting community. For many, it will solve problems. Perhaps it will not be a detriment to the industry either. It may just end up being a new and useful tool. Like moving from the simple transits of the past to the GPS connected ones today. Higher skill gets more money. Perhaps that will be the case here too.
Very simplified versions of an instrumented (azimuth and elevation)laser sight have been in use for many years in the remodel industry for residential buildings. Manually operated and tripod mounted these devices can map out that not-quite-square countertop so the fabricatior can make a perfect replacement. The concept isn't brand new, but the automation of it is.
When they send in the mapping robots to scan the underground structure in the movie "Prometheus," you can see that mapping bots are going to be the norm. Ease and accuracy is key. Though, in the movie the bots used some sort of laser scanner system that recreates the whole surface while flying through tunnels at high-speeds. Today's bots are not at that level. When they are... architecture, exploration, and the military will be revolutionized.
Perhaps the application of robotics and lasers can provide an improvement in the accuracy of construction, and it would be valuable if it would actually deliver. My observation is that the errors are mostly made far downstream from the project management and supervision. The problems seem to happen at the actual point of application of materials, either through inadequate following of the measurements or through ignoring the measurements completely.
BUT being able to produce very accurate measurements will offer the chance to reduce the problem, so it is a potential source of benefit.
My company has been doing work in inside and outside construction with our robots. We had multiple inquires at the RoboBusiness conference this year on small bots for doing floor lines for the interior walls.
There is no doubt in my mind that better methods are desperately needed when workers make necessary layouts relative to CAD plans for building construction. We have examples in our city relative to huge mistakes during construction with thousands of dollars lost in penalties due to corrections needed. In our town, unions are very strong and the thought a robotic system may take the job of a union member would be a real issue. I do hope this augments the process and creates value added relative to the construction industry. Time will tell.
Thanks for all the comments, everyone. I think there is definitely a unique value proposition in this technology. Lots of times a new company says it's doing something completely different and filling a real gap in the market, but I think in this case (especially from what I'm hearing) that it may actually be true.
Using almost 200 light-emitting diodes in the front and back of the new 2014 CTS, Cadillac designers are showing how LEDs can change the character of a vehicle.
We looked at a number of sources to determine this year's greenest cars, from KBB to automotive trade magazines to environmental organizations. These 14 cars emerged as being great at either stretching fuel or reducing carbon footprint.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
