@Ann: Okay, apparently you learned some highly non-standard definitions. According to Instron's glossary of materials testing, modulus of rupture is synonymous with flexural strength. If you Google "modulus of rupture," you'll see that this is the most commonly used definition. Clearly, "the flexural strength is zero" would not be a correct statement.
The derivation of the most widely-used modulus of rupture formula assumes that the material deforms in a linear and elastic way, so the formula no longer applies after the yield point. However, this doesn't mean that "the modulus of rupture is zero"; it just means that the formula no longer correctly predicts the stress.
As far as "catastrophic failure" goes, the most common definition seems to be "(sudden) failure from which recovery is impossible."
Give me any material, and I guarantee I can find a way to make it fail such that you'll never get it back into its original shape. Hit it hard enough, and it will fail catastrophically.
I've also noticed that some earlier ideas and technologies are being revived,and given another chance. Some may have been inventions that were in advance of their time.
@Ann: The fact that something bends before it breaks doesn't mean that it doesn't have a catastrophic failure mode -- it just means that it bends first. If you continue to load it, it will fail catastrophically, sooner or later. (Steel bends before it breaks, too, but you can point to any number of catastrophic failures of steel structures).
And "the modulus of rupture is zero" is just plain wrong. As I said, modulus of rupture is a measure of the load-carrying capacity of a beam. If the load-carrying capacity were zero, it would be useless.
Modulus of rupture just isn't a useful number for something that yields before it breaks, since the equation assumes no yielding.
TJ, thanks for the clarification. Determining that would probably take a detailed lifecycle analysis. Although these are now voluntary, and not nearly as common as many of us would like, I hope that someday they'll be required as an item on the data sheet.
The original question was worse for the environment - structural members made from wood or the composites described in the article.
The lumber industry sells itself as renewable because the companies plant trees to replace the ones harvested, and the renewal process is pretty straight forward - Cut down a forest, make lumber, plant seedlings in the now-cleared area, come back in 20 years or so and repeat.
IF the composites are made from organic feedstocks, they may be the equal of wood's impact on the environment. If they're made from petrochemicals, one would probably have to say they have a larger impact.
Lou, I thought the hurricane-resistance use was one of the most intriguing and unique about this material, aside from the more mundane uses like deck replacement. Chuck, this is not aimed at high load-bearing structural components such as bridge beams: as we state, it's for lighter construction uses such as decks and pontoons.
Interesting development. Nice to see these sort of efforts moving forward. They may not always be the most cost effective, but it's a step in the right direction. I wonder if this is one of those "we can do it in the lab, so let's see if we can sell it" sort of things or if they actually had a specific market in mind.
By refining topologies and using new fluid technology, Moog's new peak sine drive controller increases available power without increasing controller volume.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
