Is there an industry need for a ZigBee Certification test agency or certified tester recognition to not only provide the obvious technical compatability and other cert issues, but also consulting, turn-around or cost related issues. For example, can one join ZigBee alliance and develop a Cert Testing/Certification Consultancy that does the certification testing ...
I would prefer to see a button press or some other more robust mechanical - pill release mechanism that counts and semi-tamper / OD proofs any sort of medication. It seems like with any spec, if you touch it, you (may / can) incur liability, fitness for intention, implied warranty and etc.
Good presentation -- all through the 5 sessions, doubly so when coupled with the ISM class. I would like to see a slide or two with a high level flow diagram of network design process - from spec'ing out a system, chip/module selection, firmware issues, tradeoffs, implementation ideas ... network architecture issues, and thru commissioning on to test and eval (toss in compliance and cert too maybe) ...
Sub 60 minute classes work fine (maybe 50 minute limits) for archived functions and would be acceptable for most online presentations I have participated in ... not sure if more than 30 minutes interferes with some attendees lunch periods or interest / attention levels ...
Thanks all for your participation - I look forward to "seeing" you in future classes here at the Digi-Key CEC!! Thanks again Rob - honey lemon tea! That is my cure (real honey and real lemon juice - no coffee and no alcohol)
The one q I see is about where the test 'sniffer' goes for analysis. Anywhere within range of the PAN coordinator. I like to put it in the center of the physical network. It is not a node (although some silicon-mfr-provided ones tap into the coordinator, I don't like that. It is like scope probe capacitance - can fix or break a network!
I recently discovered products from Schmartboard that permit soldering SOIC chips or even 100-pin chips onto a 0.1" pitch breakout board. Great for prototyping.
Where the analyer is located?; Is it taking the RF signal at any location in the network or connected directly to the Cordinator via USB port or LAN port?
In case any of you have to leave early, just a note that I can answer questions later (after today's Q&A) and am available as a consulting and training resource. My email is c.j.lord at ieee.org and my new company (launching in January!) is Blue Ridge Advanced Design and Automation (http://www.blueridgetechnc.com/). AND - we are talking about a ZigBee Part Two with some examples of design! - coming in 2013 to this curriculum!
-The streaming audio player will appear on this web page when the show starts at 2pm eastern today. Note however that some companies block live audio streams. If when the show starts you don't hear any audio, try refreshing your browser.
Hope all have a great Holiday season. The information and discussions this week have been very good and eduscational. Thanks, from sunny and cold Huntsville, Al.
Andrew Morris designed a circuit that could detect a stroke victim's groan and convert the sound into a signal so caregivers would know when help was needed.
New disc magnet motors fit into the design trend of stepping up to closed loop performance while maintaining the cost advantage of stepper motor technology.
At the Design News webinar on June 27, learn all about aluminum extrusion: designing the right shape so it costs the least, is simplest to manufacture, and best fits the application's structural requirements.
On April 21, NASA launched a novel project, putting into orbit three satellites that employ an off-the-shelf commercial smartphone as the control system.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
