HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
User Rank
Platinum
12/30/2012 6:09:16 PM
NO RATINGS
Good points about adaptive gains, tuning and resonances.  I've often seen that the effect of mechanical resonances and changes over time are not taken into consideration when tuning a servo.  The problem is that nine times out of ten you can get away with it, so the tenth time seems like a "mystery" when it occurs.

User Rank
Iron
Re: Friction is a problem as well
12/21/2012 3:34:31 AM
NO RATINGS
I have been thinking more about this rubber string analogy and there was an error in my earlier post too.

The system consists of two masses, the ball and your hand, and a spring between them, the rubber band. Your muscles provide the force to your hand that is moving it. In a servo drive the force is the air-pap torque, the hand corresponds to the inertia of the servomotor's rotor and the ball corresponds to the driven load. The rubber band corresponds to the shafts and the coupling between the motor and the load.

Now when you slowly use your muscles to move your hand up and down the ball will follow. When you increase the frequency of the movement you will find that it becomes more and more "stiff", that is, more difficult to move your hand although the ball is moving up and down. This is the anti-frequency resonance where it is difficult to get the hand tomove. By increasing the frequency further it becomes again easier to move your hand and the amplitudes of the hand and the ball oscillations increases a lot when the frequency is approaching the resonance frequency. Above the resonance frequency the ball movement decreases and your muscles are moving mainly your hand.

The anti-resonance frequency makes it difficult to control the motor movement near and above it and thus limits the dynamics that is possible to be achieved. Note that the anti-resonance frequency is defined only by the torsional stiffnesses of the coupling and the shaft and the inertia of the load. Thus the servo control system cannot improve the control response beyond that. As a rule of thumb the shortest possible response time of the speed control is the inverse of the anti-resonance frequency.

Reduction gear is often used with servo drives. The reduction gear decreases the ioad inertia seen on the motor shaft. Thus in practice the anti-resonance frequency is important only for servo drives that do not have reduction gear.

User Rank
Iron
Friction is a problem as well
12/17/2012 4:12:01 AM
NO RATINGS
Don't forget friction! Friction is a nasty thing that makes accurate position control difficult. Slip stick itself is one of the reasons for growling at low speeds. However, sometimes a dither (vibration) signal is added to the torque reference in order to keep the mechanical system in a small movement all the time. This avoids the slip stick phenomena but unfortunately has audible noise as byproduct.

By the way, there is a slight error in the explanation of the Bode plot (apparently this is a transfer function from motor air-gap torque to motor speed). The plot line below about 20 Hz describes the motor and load moving together as one piece. Around 29 Hz only the motor moves but not the load (this frequency is also known as anti-resonance frequency). Between 29 Hz and 53 Hz the load is more and more accelerating when the motor is decelerating and vice versa thus finally reaching the resonance at 53 Hz. Above 53 Hz the plot shows more and more only the inertia of the motor.

You can check this with the rubber band and ball. If you move your hand very slowly up and down, the ball will follow. When you increse the frequency you will find there is a frequency where your hand moves but the ball does not move. This is the anti-resonance frequency. Increasing the frequency still you will finally get into resonance frequency where the ball is moving very much even when your hand movement is small. Increasing the frequency yet higher (if you can) you will find that the ball is again more or less standing still although your hand moves a lot.

User Rank
Blogger
12/13/2012 3:41:38 PM
NO RATINGS
Wish I could afford a driver like this one. I accidentally hit the end of travel on one of my servos on my CNC mill. The momentary stall ended up letting all the "magic smoke" out of one of my servo drivers. A driver that would properly compensate for drive error like the above one would be most handy.

C

User Rank
Blogger
12/13/2012 2:43:41 PM
NO RATINGS
As long as a servo drive permits access to and real time changes in its gains, then it's not strictly necessary to have a modern servo drive in order to take advantage of the concept. The system controller could change the gains and feed them to the drive.  It's not as elegant as a self-contained drive, but it does permit use of this neat concept.

User Rank
Blogger
More capable microcontrollers
12/13/2012 10:28:07 AM
NO RATINGS
Marcus, thank you for an informative article.  I was just at a seminar given by a semiconductor vendor on a new microcontroller targeted at the motor control market.  These incorporate motor control timers as well as fast A/D converters.  All of these are built in to the SoC, so that the measurement and correction strategies you discuss can be implemented.

 Partner Zone
Latest Analysis
Days after a massive, distributed denial-of-service attack took down dozens of major websites around the country, ARM Holdings plc is rolling out a pair of new processor architectures aimed at shoring up IoT security.
Dow Chemical and several other companies have launched a program in Omaha, Neb. to divert about 36 tons of plastics from landfills in its first phase, and convert it into energy used for cement production.
Both traditional automation companies and startups are developing technologies to improve processes on the factory floor, while smart sensors and other IoT-related technologies are improving how products are handled during transport and across the supply chain.
Remote monitoring now looks beyond the individual motor or conveyor and instead views the process from end to end.
BASF is partnering with Hyundai on a high-performance concept car that showcases both eco-friendly, sustainable materials and materials to enable lighter weight cars.
More:Blogs|News
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 10 - 14, Embedded System Design Techniques™: Getting Started Developing Professional Embedded Software
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course September 27-29: