Since trying to use a paper clip was mentioned I am assuming that the drive in question was the optical drive and therefore the power cable in question would be an internal power cable not an external power cord. Power cable routing/XBox unit assembly and initial power cable assembly would be the most likley candiadtes for failure and there should be no need for strain relief. Usually this type of failure can be traced down to incorrect cable assembly.
And did you know a common problem is that people put heavy objects on data cords - flattenning those zeros so they look like ones? Seems to me we could have better quality material to prevent that...Okay, I'm kidding...need more coffee LOL!
But seriously, I agree - strain relief is a real problem that is really so fixable...it is annoying! Used to be "check the cord first" was just not thought of - but now it is.
I've seen an increase in cord problems due to no built-in strain relief on a variety of consumer electronics devices, including some computer peripherals. It's really really annoying, since many of these cords are not wound around each other. They're just not lined up perfectly flat all day. It's also really really annoying since cords on all electric and electronic devices used to be a heck of lot sturdier.
Woo Hoo! Pong! If you set the paddles just right it would play itself which was pretty funny when you speeded it up and it came with a cool plastic rifle too. We were the first kids on the block to get one and thought it was totally cool. That would be the 70's...
Actually, I think your comment may be right on target, "I suspect it has to do with the lack of strain relief of the cords wound around each other." In the last year I have seen a blow dryer and a battery charger both fail due to lack of strain relief of the cords...its really frustrating to see such a simple but essential concept for longevity disregarded when it could so easily be fixed.
We don't even part swap anymore - we just throw away things when they quit working and don't think twice. I remember when my printer went out after only two years of light service - I couldn't believe it. My old faithful HP had lasted 5 years or more. When the sales person at Office Depot informed me that two years was about right - I wanted to say, "Beam me up Scotty - there's no intelligent life here!" It's a different world...I guess some folks would say three years on your XBox is stellar - great job finding a fix!
In troubleshooting, always start with the simplest solutions first. Checking the power cord is always first.
Good to know, just in case my XBOX happens to fall victim to the same issue.
But, I must admit, I don't use it much these days. It was almost exclusively a Netflix streaming device. Jokingly referred to as the NetflixBox. But for $60 a year for just that seemed crazy. So, I ended up just getting a used "Boxee" from a friend. Now I can watch Netflix for free, and stream movies off of a USB drive or SD card.
Your comment about lasting until the next generation of system comes along is interesting. These devices don't really need to last long, do they? Few people stick with an old system becuase the new ones are generally much more attractive in features and performance. They also generally run the games from the last generation. I have even found that there are emulators for old game systems for the PC. If you have a powerful graphics processor on your PC, then this becomes feasible. You can even use the controllers from the older systems on the PC.
Fixing the system by taking it apart is not very comonly done. Many of the kids I know who are into this would do that, though. I don't think they are a representive sample. Probobaly all future engineers.
Industrial trade shows, like Design News' upcoming Pacific Design & Manufacturing, deserve proper planning in order to truly get the most out of them as marketing tools. Here's how to plan effectively.
The series now can interface with a wider array of EtherNet/IP-compliant hardware across many industrial sectors, including factory automation systems, plastic injection molding apparatus, and materials-handling equipment.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.