HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
ttemple
User Rank
Platinum
Re: good integration
ttemple   12/12/2012 11:12:00 AM
NO RATINGS
Cabe,

I have not experienced problems with noise in Animatics motors, but heat can be an issue.  Under certain conditions the motors have heat related problems (the heat kills the controller, I think).  I used some in an application where there was a lot of regeneration current and a high duty cycle.  The motor life was greatly diminished in this application because of the heating.

One nice thing about the motors is the simple wiring. The power to the motor is unregulated DC (2 wires), and 3 wires for communication.  No 3 phase motor cable and no encoder and/or hall sensor cables, etc.  Additionally, if you have end of travel and/or home switches, they go straight to the motor.

Elizabeth M
User Rank
Blogger
Re: good integration
Elizabeth M   12/12/2012 3:21:20 AM
NO RATINGS
Sorry, Charles, I have to say I don't know. Perhaps STMicroelectronics could help you with this question?

Cabe Atwell
User Rank
Blogger
Re: good integration
Cabe Atwell   12/11/2012 3:47:29 PM
NO RATINGS
TTemple,

I didn't like animatic's idea of integrating the controller at the motor. Where intense electromagnetic fields are blasting the local area. Maybe the board is shielded, maybe not. However, I would like to see the motor's power supply at the motor itself and move the drive electronics away.

BobDJr,

Thanks for the link. I will look into this ASAP.

C

jcdammeyer
User Rank
Silver
Not enough in one package
jcdammeyer   12/11/2012 11:23:55 AM
NO RATINGS
A useful part perhaps for some applications but what does it do that a dsPIC c/w embedded CAN port cannot?  External winding drivers are still required.  A processor that does SPI is still required.  And unless one mixes P and N channel FETs the high side needs to be 12V above the gates so external support devices and drive FETs are still needed.

What would be really useful would a be device that can microstep a motor to 1/16, have step/dir inputs and have coil drivers with 3.5A and 80V-100V rating.  There are a few devices out there that do 2.5A and 24V but exceed that voltage at your peril.

John

Consultofactus
User Rank
Iron
Re: good integration
Consultofactus   12/11/2012 9:56:45 AM
NO RATINGS
Only if you can wedge the FETs or IGBTs in as well. This device drives external "6 packs".

BobDJr
User Rank
Gold
Re: good integration
BobDJr   12/11/2012 9:44:51 AM
NO RATINGS
Here's a link to the ST evaluation board for the L6480:

http://www.st.com/internet/evalboard/product/254209.jsp

tekochip
User Rank
Platinum
Re: good integration
tekochip   12/11/2012 9:26:45 AM
NO RATINGS
Good find ttemple.  Tuning a stepper controller for a particular motor can be real pain, and if you're not a EE, a plug and play solution is the way to go.
 
Just about every silicon vendor has a "motor controller" part, whether it be for BLDC motors or steppers.  What makes the difference is how quickly you can get the part to spin a motor and how much it costs to do it.  As mentioned in the article, the biggest problem is the resources required from the micro to spin the motor.  Another problem, not often addressed, is debugging.  Many of the motor controller parts do not gracefully remove the load when debugging, so that breakpoints and single-stepping can have disastrous results.  This part looks to be a very high-end solution that may not fit into smaller motor applications like those used in the gaming industry, but would really work well in medical and robotics.


ttemple
User Rank
Platinum
Re: good integration
ttemple   12/11/2012 8:29:14 AM
NO RATINGS
Animatics (http://www.animatics.com/) has been building the controllers inside the end cap of stepper and servo motors for quite a few years now.  You connect a power source and a communication cable to the moter, and off you go.

TJ McDermott
User Rank
Blogger
Re: good integration
TJ McDermott   12/11/2012 12:07:17 AM
NO RATINGS
Good integration is right.  The controller can be built into the stepper motor, maybe even as a plug-in option.

Charles Murray
User Rank
Blogger
Re: good integration
Charles Murray   12/10/2012 6:58:57 PM
NO RATINGS
Elizabeth, any idea what the cost differential would be between this single-chip design and a typical multi-chip design?

Page 1/2  >  >>


Partner Zone
Latest Analysis
For city dwellers, finding a parking space can be a time-consuming and downright exasperating task. Now, however, engineers may have found a solution to that old urban problem.
Manufacturers have to manage a wide range of data, and unstructured data -- from PDFs to video files -- has become a big challenge as the new world of Big Data emerges.
Answer this question, and more, during Design News’ Focus on Fundamentals course -- From Rapid Prototyping to Quick-Turn Production: A User’s Guide -- June 2-4. Sponsored by Proto Labs.
In his keynote address at the RAPID 2015 conference last week, Made In Space CTO Jason Dunn gave an update on how far his company and co-development partner NASA have come in their quest to bring 3D printing to the space station -- and beyond.
On Memorial Day, Americans remember the sacrifices the US armed forces have made, and continue to make, in service to the country. All of us should also consider the developments in technological capabilities and equipment over the years that contribute to the success of our military operations.
More:Blogs|News
Design News Webinar Series
5/21/2015 11:00 a.m. California / 2:00 p.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
6/3/2015 8:00 a.m. California / 11:00 a.m. New York
6/11/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jun 8 - 12, Everything You Ever Wanted to Know about Filters
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course June 2nd-4th:
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service