HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
REGISTER   |   LOGIN   |   HELP
Page 1/2  >  >>
jmill
User Rank
Iron
XBee modules
jmill   1/10/2013 1:04:57 PM
NO RATINGS
I saw you have an XBee module in your model car.  Cool.  Design News contributor Jon Titus has a book, "The Hands On Xbee Lab Manual," that has a lot of good information about to how to use these small wireless devices beyond basic controls.  Excellent project and inspiring for fellow students and experimenters.  Nice job.

mrdon
User Rank
Gold
Re: Cool
mrdon   12/17/2012 3:13:14 PM
NO RATINGS
Cadman-LT, I agree. That's a pretty cool car and the author is correct about it being fast. I'll be sharing the video and article with my ITT Tech Microprocessor and Microcontroller students.

armorris
User Rank
Platinum
Re: Not enough information
armorris   12/16/2012 4:41:27 PM
NO RATINGS
Thank you, Matthew for the clarification. I look forward to learning something from your software code. BTW, what is a "github"? I'm not familiar with all the new terminology.

matthew katzenstein
User Rank
Iron
Re: Not enough information
matthew katzenstein   12/16/2012 4:09:15 PM
NO RATINGS
the instructions are written to be broad because the different models of RC cars have different boards and board layouts however MOST use the same chip so the instructions are for taking over control from this type of RC chip, thus the instructions can be used for many different types of RC cars you simply attach the wires to the same pins on the IC chip and you are ready to roll 



matthew katzenstein
User Rank
Iron
Re: good use of electronics
matthew katzenstein   12/16/2012 2:26:50 PM
NO RATINGS
kinda? the PC board is to hold the headers in place so they dont shift around and you can connect them all at once. 

 

i didnt include the arduino in the BOM because this will work with ANY 5v microcontroller and is not arduino specific 

i believe i did include code when i sent in my materials for the article but i will look into that. the code is REALLY simple so with about 5 minutes you could knock out some basic fwd bckwd left right control on any microcontroller  

i will soon setup a github so i will put code there

Nancy Golden
User Rank
Platinum
Re: good use of electronics
Nancy Golden   12/11/2012 10:19:32 AM
NO RATINGS
And while I would also have liked more details - I think Matthew did a great job on pointing out "Gotchas" in his instructions such as:

"The circuit uses negative logic so off – high on – low. Do not bring forward and reverse pins for the same wheel. It will cause a short."

Those minor details can be pretty important...

Cadman-LT
User Rank
Platinum
Cool
Cadman-LT   12/10/2012 2:04:12 AM
NO RATINGS
Cool project Matthew!

Charles Murray
User Rank
Blogger
Re: good use of electronics
Charles Murray   12/7/2012 6:48:20 PM
NO RATINGS
Details or not, it's still a cool application. Matthew, the bill of materials shows a PC board for $2.63. Is that the Arduino board?

Cabe Atwell
User Rank
Blogger
Re: good use of electronics
Cabe Atwell   12/7/2012 6:23:49 PM
NO RATINGS
I was just speaking to a colleague of mine who did this exact project this past summer.  He is a big RC fanatic. I hope Arduinos become mainstream in RC development. Who knows where RC will go after that.

C

NadineJ
User Rank
Platinum
Re: good use of electronics
NadineJ   12/7/2012 3:14:29 PM
NO RATINGS
The good thing about the limits on the performance is that kids tend to push those limits.

I agree with everyone's point that there aren't enough details here. 

Page 1/2  >  >>


Partner Zone
Latest Analysis
Lumus and eyeSight have partnered to create consumer-grade devices that offer all the prime functions of smart glasses without the bulk.
VisLab joins the autonomous car effort with the DEEVA prototype.
NASA and Boeing developed a huge, carbon composite cryogenic fuel tank for deep space missions, and started testing it last month. The 18-ft cryotank will enable heavy-lift launch vehicles to send both humans and robots into deep space.
Focus on Fundamentals -- a new Design News webinar series -- kicks off April 29 with How to Select Drives for Robotics Applications. Don't miss it!
Research and other advancements in the realms of robotics, diagnostic and treatment devices, nanotechnology, and medical implants may one day make humans superior versions of their natural selves.
More:Blogs|News
Design News Webinar Series
3/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
2/27/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
12/18/2013 Available On Demand
11/20/2013 Available On Demand
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Apr 21 - 25, Creating & Testing Your First RTOS Application Using MQX
SEMESTERS: 1  |  2  |  3  |  4  |  5


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: April 29 - Day 1
Sponsored by maxon precision motors
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service