Use the circuit in figure 2 as a reference. The strings are essentially tied in parallel. R8, D9, D10, etc is the primary string and R10, D46, D47, etc are the secondary string. Both strings connect to the source of the MOSFET, Q2. Therefore, the voltage applied to all strings would be the same and if the strings are identical, the current through them will also be the same, even though only the current through the primary string is sensed (by the voltage across R8). D9 is being used as the voltage reference to control the voltage across R8. All added strings would be connected in the identical way as the string containing R10.
The voltage on R8 is sensed by Q1 through R2 and R3 while Q2 is switched on. The switching threshold is set by the voltage on Q1's emitter.
I didn't follow up on your last comment, about adding a complement to R8 and D9 to paralleled strings. This would just be a series LED and resistor, not tied into the FET drive, right? To balance the voltage applied to the strings?
You can take 2 polarized caps of double the desired value and connect them in series such that both -Ve terminals are connected together. The resulting equivalent capacitor can be used as a Non polar capacitor of desired value. I would use rated voltage on each to be safe and also I have always connected only -ve terminals togther although it may work with both +ve terminals connected as well.
If you want to drive just a few LEDs, here is the link to a 20mA LED ballast circuit that I created many years ago and still use nightly to drive three white LEDs. It's even simpler than the featured circuit, but it's not suitable for large strings of LEDs. Please put a 100 ohm, ¼ watt carbon composition resistor in series with it to limit in-rush current and to act as a fuse in case of a short. Mine has one, but I don't know why it's not in the schematic. The website has not been responsive to changes or new submittals. Put a low-value pot in series with R2 and R3 if you want dimming. Like the featured circuit, this circuit is not isolated from the power line.
The SCR can be deleted if the LEDs are permanently wired and you don't need dimming. In my application, the LEDs were switched off after the ballast circuit, requiring the SCR voltage limiter to keep C2 from exploding. You can replace the SCR with a zener diode, but then the circuit would consume even more power when the LEDs are turned off. The LED current will be approximately 20mA per microfarad of C1. The LED current will go down, requiring a larger value for C1 if a significant number of LEDs is added. Also, the peak SCR current will increase as more LEDs are added.
Hi, John, You don't seem to realize that Radio Shack is not "making money." It's losing money and its stock has fallen from $13 to $2 a share in the last year. It's fighting for its life! It's business model needs to change fast. People can buy cell phones in lots of places. I want Radio Shack to *be there* in two years as a brick and mortar store and that's why I offered suggestions. They need to mix Sparkfun, Adafruit and brick and mortar into a lively model.
Keep up the good work on your electronic designs. I'm working on something new myself.
For 3D printing to make the jump from rapid prototyping to manufacturing, engineers will need to find easier ways to move products from their CAD screens to their printers.
Gigabit and PoE are two networking technologies moving ahead in tandem as industrial users power remote Ethernet devices such as IP security cameras at 1,000 Mbps over existing CAT5 cable.
New versions of BASF's Ecovio line are both compostable and designed for either injection molding or thermoforming. These combinations are becoming more common for the single-use bioplastics used in food service and food packaging applications, but are still not widely available.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
2 
