There is a basic flaw with the very concept of surge brakes, which is that there is no way to apply them without braking the tow vehicle. I am aware that they allegedly have a breakaway application device, but that is of no use when you simply need to apply brakes on the trailer, which you need to do non the occasion that the trailer is forced into an oscillation mode, either by the shockwave from a truck passing too close, or a number of other causes. And if your vehicle brakes fail, that surge brake is not available to slow you at all. So the first step is to replace the surgen brake with a system that can work. One "older concept" system uses the tow vehicle's power steering pressure and a control valve piloted by the tow vehicles brake system pressure to activate a hydraulic cylinder on the trailer that drives a secondary master cylinder. That system can have an electrical valve to provide remote operation of the trailer brakes, for emergency and parking use. Other systems have used tow vehicle engine vacuum to drive the trailers master cylinder. Of course, all of them cost more than a surge brake system, but all of them beat driving without any brakes.
I have stopped nmy van, while pulling a travel trailer, using the trailer brakes alone. It is not nearly as good as the four-wheel brakes were, but I did get stopped. That was when a front brake line bust on my 1985 Dodge van. Contrary to the claims, when you lose front brakes, you have no back brakes either. At least, not on a Dodge from that model year.
Warren, Ann and tekochip: Here's some more info about the driving conditions I was experiencing when the trailer brakes started smoking. That day I had only driven a short distance with the trailer, all on level roads. Before entering the freeway, I had driven less than two miles from home through town at a maxim speed of 35 mph. When I entered the freeway, the brakes started smoking within the first 500 yards. I was not using the brakes because I was just getting up to freeway speed.
Regarding riding the brakes, some interesting dynamics occur with surge brakes. In steep downhill situations, controlling the speed of the tow vehicle by using a low gear and not riding the brakes does not avoid the potential for the trailer brakes to overheat. Regardless of how the speed of the tow vehicle is controlled, if it creates a great enough resisting force against the trailer inertia, the surge actuator on the trailer will apply the trailer brakes.
One reason I was so surprised with the overheating was that just the week before this problem occurred I had towed the boat on a 500 mile trip. That trip included mountainous roads and 100 degree air temperatures. Although there were problems with individual brakes on the trailer, there was never any problem of all four wheels smoking. Interestingly, this trip included going down "The Grapevine" grade on Interstate 5, the main north-south highway in central California. This grade is about 6 miles long, has a 6% slope, and includes escape ramps for runaway trucks whose brakes fail. Despite the potential for the trailer brakes to overheat, the brakes appeared to handle it fine, with no smoking.
tekochip, that's a whole 'nother subject that many drivers have complained about here: tight curves on exit ramps, as well as very, very short exit ramps in some places. OTOH, when driving in New England, especially Massachusetts, many years ago, I was amazed at how poor the freeway exit signage was in letting people know what exits to take to get to specific places, (XYZ village name instead of Highway XX North, Highway XX South). It reminded me of some areas of Britain: you had to be a local to understand where you were going and which road took you there. The last time I drove there, in the early 2000s, I did see some improvement.
Warren, no offense taken; it was clear you don't drive the kind of roads I do. Those "Deadman's Curve" labels are not symbolic or imaginative, so my luck was actually quite good. The big problem I see is not enough warning symptoms before failure occurs, as well as brakes not designed to handle the amount of use required on long descents, no matter how much you use lower gears. We've got deer, too, up here and one took out the entire front end of my first husband's 1965 Mustang, which had a V-8 and a heck of a lot of steel in it. I bet you've got some great mud stories, though--and that's *not* sarcastic.
Warren, the first time I was young, inexperienced on mountain roads, and alone. I didn't know how to use lower gears, even on an automatic (both cars were automatics). In both events, only one of the brake sets went out, which is why I live to tell the tale. The second time I was highly experienced and not alone--fortunately, the guy who was about to be my husband said not a word and let me do my thing--and people had died on that slalom-like section--so we lived. In both cases, there had been no warning signs of any kind, such as brake noise, and the second car was well maintained. I know several people who've had similar experiences, more than once, and Highway 1 has more than one "Deadman's Curve" sections (title of a Beach Boys song way back). Perhaps your mountain roads aren't as steep or as windy as they are in the Coastal Range in California.
Lantronix Inc. has expanded its line of controllers for sensor networks with the release of a rugged controller that improves management of automation systems used in a number of industries, including manufacturing, oil and gas, and chemicals.
Inspired by the hooks a parasitic worm uses to penetrate its host's intestines, the Karp Lab has invented a flexible adhesive patch covered with microneedles that adheres well to wet, soft tissues, but doesn't cause damage when removed.
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is