This article brings back memories of ESD testing for me. At one place I worked we had a fairly sophisticated ESD tester and you could program in pin combinations and set voltage values and do just about anything you wanted. It came with different fixtures to fit different packages and you got your results stored to disk. Another place I worked at had a hand held ESD tester. You set your voltage and placed the tester head on the pin you wanted to zap (you literally put the device in a clamp and held the tester to each pin - you could program voltage and length of pulse if I recall correctly) and it was fun to use. You would then take the part for testing on your own test set. I always got a good laugh at the hand held model - it had a warning printed on the front "DO NOT USE AS A CATTLE PROD."
The author of the article has made some good points. We have come a LONG WAY in ESD protection but a designer should definately check specs to see if his application is in danger of getting zapped out of commission during normal use.
Chuck, the data sheet is important becuase it is the published detail on a product. This is what the vendor claims in public the device will do. So, as you point out, you need to read all of it. Depending on the device, they can be very long. There is also a lot of fine print because of the implications. If the customer has a problem and did not read the data sheet correctly, then it is their problem. If they read it correctly and had a problem, then it is the vendors problem.
I couldn't agree more. In my past experience as a design engineer, I've seen several of my peers select protection devices that ended up having double the capacitance from what they expected.
The value touted on the first page of the datasheet made for nice marketing, but that was only the capacitance of a single diode. When the protection device was connected in circuit there were 2 diodes per data line and therefore twice the capacitive load. Needless to say, they had to go back to the drawing board when their designs failed due to poor signal integrity!
You make a good point about the marketing aspects, Chad. In talking to you for this article, I realized I would have been one of the engineers who blindly trusted the numbers on the datasheet. Those numbers are, after all, data. But I suppose even data can be misleading, especially if we only present the data that puts us (or our product) in the best light.
A lot of engineers I know do not give the datasheet a full examination. Simple ESD protection is usually not on their minds at all. Just making it work seems to be the only focus. In fact, I have seen countless times where a static shock from handlers of the electronics destroy prototypes. Then everyone is head scratching over why it doesn't work.
Adding to this article, in addition to proper design application, there also needs to proper ESD handling procedures, training and equipment tests during manufacturing assembly. Improperly trained assemblers may not realize how easy it is to damage a sensitive electronic component. Also, regular ESD equipment checks need to be performed at each appropriate assembly station.
I remember one case where ESD damage was occurring even though proper foot straps and wrist straps were present. Upon further examination, it was found that the dissipative ESD floor wax was wearing thin and became ineffective (causing everyone to have a false sense of security when their foot and wrist straps were properly being used).
I think you make a good point, Greg - it's very important to enforce the procedures for ESD protection during manufacturing. Sometimes we would get some guy who would enter an area thinking that the rules didn't apply to him - and then people wondered why our RMAs showed ESD damage...
Yes, the dissipative floor wax is a very expensive product and must be reapplied on a regular basis. However, its a great way to control static through ESD shoes, shoe straps or chains hanging from PCB carts.
Greg's points are the best action for dealing with static sensitive devices. But Its both smart product design, AND preventative measures during fabrications.
When PCBs are open & exposed (during manufacturing) ESD wrist straps, ESD jackets, boot straps, and grounded desk pads must be in place. Any manufacturing center dealing with open electronics & fabrication processes has all of these elements implemented on the production floor.
After finished goods are distributed to consumers, the product envelope must be sufficiently insulated to prevent that "carpet-static" and other ESD effects. That goes back to the effective design of the housing enclosures, in the first place.
A middle school team from Rochester, Mich., has again nabbed the grand prize in the annual international Future City Competition, which drew students from 37 regions of the United States, as well as from England and China.
The word “smart” is becoming the dumbest word around. It has been applied to almost every device and system in our homes. In addition to smartphones and smart meters, we now hear about smart clothing and smart shoes, smart lights, smart homes, smart buildings, and every trendy city today has its smart city project. Just because it has a computer inside and is connected to the Web, does not mean it is smart.
Are you being paid enough? Do you want a better job? According to a recent survey Manpower released just before Engineers Week, employers and engineers don't see eye-to-eye about the state of US engineers' skills and experience.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.