View Comments: Oldest First|Newest First|Threaded View
User Rank
Home use?
naperlou   11/20/2012 11:54:59 AM
Jose, this is an interesting set up.  The power and low cost of microcontrollers has allowed a wide range of very interesting hobbyist projects that would be very difficult in the past. 

Is there more detail about this controller on the TI site.  I know some guys who would be interested.

Cabe Atwell
User Rank
Re: Home use?
Cabe Atwell   11/20/2012 2:53:20 PM
I hate to pull a forum cliché, but...

I need the source on that board!

I couldn't find a link about where I can get one.  I want to use that CNC setup for some home projects (CNC mill and lathe).

On another note, I see it uses a parallel port, serial communication. That is becoming a problem with CNC setups these days. Most new desktop computers, laptops, micro-computers, and the like, do not have parallel ports onboard. In many cases, a parallel port card would need to be installed. And hopefully, the system has an expansion slot available.

What most people do is buy old, or surplus, computers from somewhere. My current CNC mill runs off of a PC I found in the garbage many years ago (Celeron 700MHz Compaq desktop). I think it is time to change how these CNC drive systems work. USB is the only way to go. So, built in support for USB to serial in a good stop-gap solution.

Just a thought.


User Rank
Re: Home use?
rv7charlie   11/21/2012 9:40:14 AM
A friend who's an engineer & runs a small prototype shop tells me that none of the serial options can function quickly enough to handle the 'feedback loop' in starting, stopping, & moving the tool. (He's rebuilding a German 5 axis mill & currently dealing with that issue.) 

Larry M
User Rank
Everything old is new again
Larry M   11/21/2012 9:47:27 AM
Ahh, yes. About 20 years ago my son and I built a robot using the stepper motors, power supply, and motor driver board from big industrial-grade daisywheel printer. We discarded the logic board and designed and built a simple interface board to interface the motor drivers to..a parallel port.

We used an eight-bit control word, where three bits allowed us to control up to eight motors (two implemented), four bits were used to control individual motor phases, and one bit indicated whether the driver should be at full power (to step) or half-power (to hold position). This design, of course, permitted forward and reverse motion, and half-stepping by energizing two phases at once.


User Rank
Re: Home use?
Island_Al   11/21/2012 10:48:33 AM
I'd like a source for this board too.  I've considered doing somthing like this myself so I can let my lathe do the work accurately while I drink coffee. My lathe did not come with change gears to enable it to cut threads.  After spending lote of hundreds of dollars, I still can't cut metric!  On the internet there is a website concerned with "electronic lead screw" kits, a single stepper controller to cut any pitch (coordinated lead screw movement). So many things to do!

Please note that parallel is not serial, but 8 bits wide, and bidirectional. I use old machines running under DOS and one would be amazed how smoking hot these machines really run as far as pure processing horsepower.

USB, while a high through put, are bogged down by multitasking.  For example you can buy a USB to parallel converter to run an older printer. But to run high speed on this bus, you can't.  Connect a scope and repeatedly toggle one bit. Very poor performance overall.

Jose Quinones
User Rank
About Source Files
Jose Quinones   11/22/2012 5:36:49 AM
Hi All,

Thanks for your comments and taking the time to read this article! In the upcoming weeks I will be finalizing the application note which will contain details such as schematics and source files. I am also studying different venues to having these boards available for purchasing on some sort of an eStore.

With regards to the USB, I will soon be posting a completely different CNC solution which revolves around USB. It is the one I am using on my 3D printer. However, the truth is as perfect as this solution is for a 3D printer, I would not use it with a router, mill, lathe, plasma CNC table. Any of the later, operate much better when using a CNC controller such as MACH3 and USB solutions have not been able to pair up with their parallel counterpart. In my experience, adding a PCI parallel port to any PC out there works perfectly fine. I have done it with 3 completely different computers (the ones I use for my CNC Mill, CNC Plasma and CNC Router) and as of today have had no problems.

Let me know if there is anything else I can help you with!

User Rank
where to post your design
mr_bandit   11/26/2012 5:37:22 PM
When you get your design done, Hackaday.com would probably post it to a very wide audience. You imply this is your design and not a TI product.

It is beefier than most of the open-source units out there (mainly for 3d printers).

You may find a good demand for this. One possible eStore is adafruit.com or the Maker Store (make magazine), esp if you open this up as an open-source or offer it in kit form.

Goto hackerspaces.org and find a hacker space near you - take it by for an intro and show&tell. You might even sell the demo unit on the spot!

Success. Looks like a good project.


Partner Zone
Latest Analysis
Major changes are happening in the world of 3D printing and additive manufacturing materials, machines, and software. If the industry -- and the design engineers and OEMs it serves -- are to grow, all three areas must become much more tightly integrated.
Americans spent more than $60B on their pets in 2015. Folks are definitely spending their money on more than dog food. We’re spending on things like dog spas and fancy toys, and as you can imagine, the wearables market is becoming well represented here.
Collaborating researchers in Australia and the United States have discovered nanotechnology for thermophotovoltaic cells that could boost solar-energy harvesting.
Time was when sports equipment was made only from common, everyday, low-tech materials. But now sports equipment has a new, high-tech ingredient that is helping players take their game to the next level.
Every now and then Design News likes to revisit some of our favorite Gadget Freak projects. Robotic hands, manipulated Kindles, and smart recycling cans round out the latest crop.
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course September 29-October 1:
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service