HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Page 1/2  >  >>
warren@fourward.com
User Rank
Platinum
Re: Good logic
warren@fourward.com   11/15/2012 5:38:21 PM
NO RATINGS
I think the one-change-at-a-time rule should be written into law,or at least a physical punishment given for ignoring it. The little or much time given to its implementation pays off more than we know!

Tool_maker
User Rank
Platinum
Re: Good logic
Tool_maker   11/15/2012 4:20:19 PM
NO RATINGS
Battar: I think you need to add a corollary, only change one thing at a time. It drives me crazy when someone makes wholesale changes that make the problem worse and then they cannot recall everything that was done so we can reverse the procedure to get back where we were and start the trouble shoot process anew.

Rob Spiegel
User Rank
Blogger
Re: Good logic
Rob Spiegel   11/8/2012 11:32:44 AM
NO RATINGS
I agree Battar. Hitting the product can be a real solution. I had a TV for a few years that needed a smack on the side every time it was turned on in order to bring up the picture. It was quite amusing to watch my kids each morning as they turned on the TV, and then smacked it on the side.

Battar
User Rank
Platinum
Re: Good logic
Battar   11/8/2012 2:08:54 AM
NO RATINGS
Rob, thats 97% for one of the 4 options. "hit it" is good for 30% - it cures bad connections and cold solder joints fast (but temporarily). As one of my colleagues was fond of saying, a fault isn't a rabbit - it doesn't run away, it always returns (that rhymes in the local lingo here).

Rob Spiegel
User Rank
Blogger
Re: Good logic
Rob Spiegel   11/7/2012 5:02:26 PM
NO RATINGS
Battar, did you mean that 97% of the time one of the four attempts works? Or did you mean that 97% of the time it's the number four try (looking at what you touched last) that delivers is the solution?

SteveG56
User Rank
Iron
Re: Good logic
SteveG56   11/7/2012 11:08:26 AM
NO RATINGS
You're right, Batter.  And I think the 97% statistic for step #4 is pretty close.  In this case the problem was on a board 5 slots away on the backplane and some time had elapsed since the previous design change.  Regarding the pesky spread spectrum clock oscillator, we were probably thinking if a little is good, a lot will be better.

Battar
User Rank
Platinum
Re: Good logic
Battar   11/7/2012 9:25:15 AM
NO RATINGS
Steve, actually you just had to follow the 4 rules of fault-finding for technicians. It's under rule 4. The rules are - 1)Turn it off, turn it on again 2)hit it 3) read the data sheet 4) look for the problem at the last place you touched before it stopped working. That usually solves 97% of all problems.

Charles Murray
User Rank
Blogger
Re: Good logic
Charles Murray   11/6/2012 6:08:54 PM
NO RATINGS
Great sleuthing work, Steve. I agree with JamesCAnder's comment below: "...intuition and experience can solve a lot of issues."

Rob Spiegel
User Rank
Blogger
Re: Good logic
Rob Spiegel   11/6/2012 5:57:54 PM
NO RATINGS
Yes, I know how that goes, Steve, when you think the problem is in one area and it's acually in another area.

SteveG56
User Rank
Iron
Re: Good logic
SteveG56   11/6/2012 5:00:44 PM
NO RATINGS
You're exctly right.  The thing was, the first spread spectrum clock oscillator (I'm not a fan of those) had a narrower "spread" and didn't cause the problem.  It was when we widened the spread, to get the emitted noise spikes lower, that the ghost images started showing up.

Page 1/2  >  >>


Partner Zone
Latest Analysis
If you’ve ever seen a retread fly off a speeding 18-wheeler, then you’ll understand the value in Freescale Semiconductor’s latest tire pressure monitoring effort.
Cost, product development rigor, the patient-as-a-user movement, and consumer electronics that include wireless connectivity are just a few hot topics swirling around medical devices. Each brings challenges that create innovation opportunities. If we briefly look at each one, we can see that one common need will be innovation in simplicity.
Tesla is expected to announce the release of a new battery aimed at powering your entire home.
The supply chain will change significantly over the next 10 years as industry 4.0 technology enhances supply chain performance, according to the 2015 MHI Annual Industry Report, “Supply Chain Innovation — Making the impossible possible.”
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
More:Blogs|News
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
May 4 - 8, Designing Low Power Systems using Battery and Energy Harvesting Energy Sources
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service