HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Comments
View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 3/3
Nancy Golden
User Rank
Platinum
Re: They can't both be bad
Nancy Golden   10/24/2012 12:32:00 PM
NO RATINGS
I agree, Rob - since part swapping is usually a quick way to verify if a part is operating correctly. I would also have been tempted to call the cable good and look further for a different problem. I have done it in the past (just grabbing another part out of a parts bin) and after wasting time verifying everything else was okay, I would return to the part I had called "good" and finally figure out that while it was not the obvious answer, the replacement was also bad. Glenn did a great job going to a KNOWN good cable to make his call - a great tip for anyone involved in troubleshooting!

Rob Spiegel
User Rank
Blogger
Re: They can't both be bad
Rob Spiegel   10/24/2012 11:00:11 AM
NO RATINGS
Good point Naperlou. Glenn will likely weigh in on this. If the cable was new but defective, you would get a powerful bias that the cable wasn't the problem.

naperlou
User Rank
Blogger
Re: They can't both be bad
naperlou   10/24/2012 10:35:01 AM
NO RATINGS
Glenn, that was good work.  I always found that there are often several different failure modes and it is important to isolate them.  The problem with the second cable is a difficult one.  I wonder if that cable was considered "new" or if it was a spare from another unit.

Rob Spiegel
User Rank
Blogger
They can't both be bad
Rob Spiegel   10/24/2012 5:56:05 AM
NO RATINGS
Good detective work, Glenn. When the replacement cable was also bad, it would have been easy to determine that the cable wasn't the problem.

<<  <  Page 3/3


Partner Zone
Latest Analysis
Some of our culture's most enduring robots appeared in the 80s. The Aliens series produced another evil android, and we saw light robot fare in the form of Short Circuit. Two of the great robots of all time also showed up: The Terminator and RoboCop.
Two students have created a voice-command system for our homes, based on the simple and affordable Raspberry Pi.
Optomec's third America Makes project for metal 3D printing teams the LENS process company with GE Aviation, Lockheed, and other big aerospace names to develop guidelines for repairing high-value flight-critical Air Force components.
This Gadget Freak review looks at a cooler that is essentially a party on wheels with a built-in blender, Bluetooth speaker, and USB charger. We also look at a sustainable, rotating wireless smartphone charger.
Texas Instruments is rolling out a new microcontroller that could make the design of sensor networks and data logging systems simpler and less costly.
More:Blogs|News
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 4 - 8, Introduction to Linux Device Drivers
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service