HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  RESOURCE CENTER  |  INDUSTRIES
<<  <  Page 4/5  >  >>
User Rank
Iron
Re: Go John!
10/22/2012 2:04:43 PM
NO RATINGS
@Dave ---

I don't mean to argue, but I think you need to re-think that.  If I place two 1K, 1-Watt resistors in series, I end up with a 2K, 1-watt resistor.  The same holds true for three series 1/3-ohm, 30-watt resistors, as in John's example.  It ends up being a 1-ohm, 30-watt resistor.

If John had started with nine 9-ohm, 10-watt resistors, and placed them ALL in parallel, I agree that he would end up with a 1-ohm, 90-watt resistor.  That's not what he describes, however.

User Rank
Iron
Re: Go John!
10/22/2012 1:06:47 PM
NO RATINGS
From your video we can see that you have done some experimentation with other batteries and LEDs.  Enjoyable video and it looks like you are having fun.

What's next for you?

-Eddy

User Rank
Gold
Re: Go John!
10/22/2012 12:55:20 PM
NO RATINGS
Hi John,

To aid in your LED lighting research experiments, here's a cool online circuit simulation website called Circuit Lab. Nice way to do paper analysis first and then model it using software. Here's the link below. Enjoy!!!

https://www.circuitlab.com/

User Rank
Gold
Re: Go John!
10/22/2012 12:39:20 PM
NO RATINGS
Hi John,

I shared your Gadget Freak video with a group of  DC-AC Electronics students at ITT Tech to get them motivated about Electrical-Electronics Engineering Tech. I wanted to illustrate the importance of doing homework, which you elegantly demonstrated, in the video based on your LED research. Keep the good work!!!

User Rank
Iron
Re: Go John!
10/22/2012 12:16:11 PM
NO RATINGS
Great job, John! Keep up the good work.

Rudy Schneider:

Huh?!?  Better go back and study Ohm's Law again, my friend!

Paralleling three equal 10W resistors will, as you agreed give you a 30W equivalent.

Placing three equal 30W resistors *however achieved* in series will indeed give you a 90W equivalent. If all nine resistors are of the same value, the combination will have the equivalent resistance of a single resistor, with nine times the power rating.

Dave

User Rank
Iron
Re: Go John!
10/22/2012 11:50:24 AM
NO RATINGS
Just a quick correction, John...

You are correct that three 10-watt resistors in parallel will make a 30-watt resistor that is one-third the resistance.  But then adding three of these 30-watt resistors in series will only result in a resistor of the original value, but STILL only capable of dissipating 30 Watts, not 90W as you stated.

User Rank
Iron
Re: Go John!
10/22/2012 10:09:48 AM
NO RATINGS
John: I am impressed with your results and would like to talk to you about your future. My name is Frank Rudolph and you can reach me on Linked-In under that name. You can reach me on Linked-In or directly at docrudolph@gmail.com, or at rudolph@beaconpower.com. At Beacon Power, our corporate charter focuses on alternative energy and sustainability.

Incidentally, if you don't already have a Linked-In account, you should get one now!! Judging from what I have read here, you have a brilliant career ahead of you, and making contacts with a network of people in the industry should start for you right now! Good job! Keep on thinking of new stuff.

User Rank
Iron
Nice work John
10/22/2012 9:36:09 AM
NO RATINGS
You're clearly well on your way to an elustrious career in electrical engineering.  Do take a look at the ol' LM317 (LM117,217,317) voltage regulator datasheet.  Somewhere in the back is a constant current regulator circuit that you will find very useful in your line of research.  Also, check out Natsemi's (now TI) boost switching regulators.  Just add an inductor, a FET, a diode and a bunch of caps to nake a voltage step-up constant current regulator.  I just finished a controller design to drive those ebay 100W modules (33V @ 3A) off of 12V power.  Keep having fun.

-Phil

User Rank
Blogger
Re: done
10/22/2012 7:01:45 AM
NO RATINGS
John: Nearly as impressive as your design is your knowledge of the different specifications and attention to using that data as part of a process around design tradeoffs. Looking under the covers and considering the pros and cons of different materials and different design choices is all part of the game and you are well on your way to becoming quite a diligent and thoughtful engineer.

User Rank
Gold
Re: done
10/21/2012 12:30:40 AM
NO RATINGS
Not sure whether you meant that those are better, or this is, but I did notice that they were over \$600 and \$1000usd respectively.  This was about \$50, and runs cold.  Those, just judging by size, would run VERY hot, and would probably not run for the claimed ~2 hours without overheating.  Either way, I wasn't claiming that this is the brightest possible light, just that it is very bright.

<<  <  Page 4/5  >  >>

 Partner Zone
Latest Analysis
Robots that walk have come a long way from simple barebones walking machines or pairs of legs without an upper body and head. Much of the research these days focuses on making more humanoid robots. But they are not all created equal.
The IEEE Computer Society has named the top 10 trends for 2014. You can expect the convergence of cloud computing and mobile devices, advances in health care data and devices, as well as privacy issues in social media to make the headlines. And 3D printing came out of nowhere to make a big splash.
Easy home automation comes with a new Kickstarter project, the smart power strip. It controls various AC outlets with a wireless controller and a smartphone app.
SUS Corp. offers aluminum frames that are designed for use in factories. The frames are used for workstations, assembly shelving, carts, and other factory and assembly support.
Amazon.com's proposed drone-based package delivery scheme is achievable, but it could face significant technical hurdles before reaching the marketplace.
More:Blogs|News
From Dell / Intel®
Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013    7
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
Most recent post: Ralphy Boy
From Dell / Intel®
Trey Morton, Dell, 4/25/2013    3
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
Most recent post: Cabe Atwell
From Dell / Intel®
Kirsten Billhardt, Manufacturing Industry Marketing Strategist, Dell, 3/26/2013    6
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
Most recent post: Ockham
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Dec 2 - 6, Protecting Your Embedded System From Hacking & Theft
SEMESTERS: 1  |  2  |  3  |  4